AS1310-BTDT-27 Ver la hoja de datos (PDF) - austriamicrosystems AG

Número de pieza

componentes Descripción

Fabricante

AS1310-BTDT-27

Ultra Low Quiescent Current, Hysteretic DC-DC Step-Up Converter

austriamicrosystems AG 

AS1310

Datasheet - Detailed Description

Energy stored during the on time is given by:

E = 0.5L(IPK)2 Joules (Region A in Figure 13)

If the overall time period (TON + TOFF) is T, the power taken from the input is:

(EQ 6)

PIN = 0----.-5---L----(-T-I---P---K---)---2 Watts

(EQ 7)

Assume output power is 0.8 PIN to establish an initial value of operating period T.

TWAIT is determined by the time taken for the output voltage to fall to 0.99xVOUT. The longer the wait time, the lower will be the supply current of

lid the converter. Longer wait times require increased output capacitance. Choose TWAIT = 10% T as a minimum starting point for maximum energy

transfer. For very low power load applications, choose TWAIT ≥ 50% T.

a 8.1.3 Output Loop Timing

The output loop consists of the main inductor, P-channel synchronous switch (or diode if fitted), output capacitor and load. When the input loop is

v interrupted, the voltage on the LX pin rises (Lenz’s Law). At the same time a comparator enables the synchronous switch, and energy stored in

the inductor is transferred to the output capacitor and load. Inductor peak current supports the load and replenishes the charge lost from the

ill output capacitor. The magnitude of the current from the inductor is monitored, and as it approaches zero, the synchronous switch is turned off.

No switching action continues until the output voltage falls below the output reference point (0.99 x VOUT).

Output power is composed of the dc component (Region C in Figure 13):

G st PREGION_C = VINI---P2---K- T----O-T---F---F-

Output power is also composed of the inductor component (Region B in Figure 13), neglecting efficiency loss:

(EQ 8)

s A nt PREGION_B = 0----.-5---L----(-T-I---P---K---)---2

Total power delivered to the load is the sum of (EQ 8) and (EQ 9):

(EQ 9)

m te PTOTAL = VINI---P2---K- T----O-T---F---F- + 0---.--5---L----(-T-I---P---K---)---2

(EQ 10)

a n From (EQ 3) (using nominal values) peak current is given by:

o IPK = -T---O----N-L--V----I--N--

(EQ 11)

c Substituting (EQ 11) into (EQ 10) and re-arranging:

alPTOTAL = -V---2--2-I--N-T--T-L---O----N- (0.9T)

0.9T incorporates a wait time TWAIT = 10% T

ic Output power in terms of regulated output voltage and load resistance is:

(EQ 12)

hn Combining (EQ 12) and (EQ 13):

POUT = R-V---L-2--OO----UA---D-T-

(EQ 13)

c R-V---L-2--OO----UA---D-T- = -V---2--2-I--N-T--T-L---O----N- (0.9T)η

(EQ 14)

e Symbol η reflects total energy loss between input and output and is approximately 0.8 for these calculations. Use (EQ 14) to plot duty cycle

T(TON/T) changes for various output loadings and changes to VIN.

www.austriamicrosystems.com/DC-DC_Step-Up/AS1310

Revision 1.8

10 - 19

Share Link: