AP7363-12 Ver la hoja de datos (PDF) - Diodes Incorporated.

Número de pieza

componentes Descripción

Fabricante

AP7363-12

1.5A LOW QUIESCENT CURRENT, FAST TRANSIENT ULTRA-LOW DROPOUT LINEAR REGULATOR

Diodes Incorporated. 

AP7363

Electrical Characteristics (@TA = +25°C, VIN = 3.3V, IOUT = 10mA, CIN = 10µF, COUT = 10µF, unless otherwise specified.)

Minimum and maximum limits are guaranteed through test, design, or statistical correlation. Typical values represent the most likely parametric

norm at TA = +25°C, and are provided for reference purposes only.

Symbol

Parameter

VADJ

ADJ Pin Voltage

IADJ

ADJ Pin Bias Current

VDROPOUT Dropout Voltage (Note 6)

VOUT / VIN Line Regulation (Note 7)

VOUT / IOUT Load Regulation (Note 7)

IGND

IOUT-PK

ISC

td(off)

td(on)

Ground Pin Current in Normal

Operation Mode

Peak Output Current

Short Circuit Current

Turn-Off Delay

Turn-On Delay

PSRR Ripple Rejection

n(l/f)

en

TSHDN

THYS

Output Noise Density

Output Noise Voltage

Thermal Shutdown Threshold

Thermal Shutdown Hysteresis

ϴJA

Thermal Resistance Junction-to-

Ambient

ϴJC

Thermal Resistance Junction-to-Case

Test Conditions

VIN = VIN-MIN to VIN-MAX,

IOUT = 10mA to 1.5A

TA = +25°C

Over temp

VIN = VIN-MIN to VIN-MAX

TA = +25°C

Over temp

IOUT = 1.5A, VOUT = 2.5V

TA = +25°C

Over temp

VIN = VIN-MIN to VIN-MAX

TA = +25°C

Over temp

IOUT = 10mA to 1.5A

TA = +25°C

Over temp

IOUT = 10mA to 1.5A

TA = +25°C

Over temp

VOUT  VOUT - NOM -5%

OUT Grounded

TA = +25°C

Over temp

From VEN < VIL to VOUT = OFF, IOUT = 1.5A

From VEN > VIH to VOUT = ON, IOUT = 1.5A

VIN = 3.0V, IOUT = 1.5A, f = 120Hz

VIN = 3.0V, IOUT = 1.5A, f = 1kHz

F = 120Hz, COUT = 10μF Ceramic

BW = 100Hz – 100kHz,

COUT = 10μF Ceramic

TJ Rising

TJ Falling From TSHDN

U-DFN2030-8 (Note 8)

SO-8EP (Note 8)

SOT223 (Note 8)

TO252 (Note 8)

U-DFN2030-8 (Note 8)

SO-8EP (Note 8)

SOT223 (Note 8)

TO252 (Note 8)

Min

0.584

0.575

—

—

—

—

—

—

—

—

—

—

—

2

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

Typ

0.605

—

50

—

190

—

0.04

0.05

0.18

0.33

1.0

—

—

3.7

—

25

25

65

61

1.0

100

170

10

174.0

52.8

105.7

87.8

28.2

10.0

18.5

17.3

Max

Unit

0.626

V

0.635

—

nA

750

240

mV

280

—

%/V

—

%/A

1.2

mA

1.3

—

A

—

A

—

—

μs

—

μs

—

dB

—

— µV/Hz

—

µV(rms)

—

°C

—

—

—

°C/W

—

—

—

—

°C/W

—

—

Notes:

6. Dropout voltage is the minimum voltage difference between the input and the output at which the output voltage drops 2% below its nominal value.

For any output voltage less than 2.5V, the minimum VIN operating voltage is the limiting factor.

7. The line and load regulation specification contains only the typical number. However, the limits for line and load regulation are included in the adjust

voltage tolerance specification.

8. Device mounted on 2” × 2” FR-4 substrate PCB, 2oz copper with minimum recommended pad layout.

AP7363

Document number: DS35059 Rev. 9 - 2

4 of 15

www.diodes.com

June 2018

© Diodes Incorporated

Share Link: