AM1S-0505SH30-N Ver la hoja de datos (PDF) - AIMTEC
Número de pieza
componentes Descripción
Fabricante
AM1S-0505SH30-N Datasheet PDF : 2 Pages
| |||
AM1S-N Series
MODELS
Single output
Models
Isolation 1000VDC
AM1S-0505S-N
AM1S-0509S-N
AM1S-0512S-N
AM1S-0515S-N
AM1S-1205S-N
AM1S-1209S-N
AM1S-1212S-N
AM1S-1215S-N
AM1S-2405S-N
AM1S-2409S-N
AM1S-2412S-N
AM1S-2415S-N
Isolation 3000VDC
AM1S-0505SH30-N
AM1S-0509SH30-N
AM1S-0512SH30-N
AM1S-0515SH30-N
AM1S-1205SH30-N
AM1S-1209SH30-N
AM1S-1212SH30-N
AM1S-1215SH30-N
Input Voltage
5V±10%
12V±10%
24V±10%
No Load power consumption 10% of nominal power (typical)
TYPICAL
CHARACTERISTICS
Ouput Voltage
5VDC
9VDC
12VDC
15VDC
5VDC
9VDC
12VDC
15VDC
5VDC
9VDC
12VDC
15VDC
Ouput Current max.
200mA
110mA
83mA
67mA
200mA
110mA
83mA
67mA
200mA
110mA
83mA
67mA
APPLICATION NOTE
Filtering
In some circuits which are sensitive to noise and ripple, a filtering capacitor may be added to the DC/DC output end and input end to reduce the noise
and ripple. However, the capacitance of the output filter capacitor must be proper. If the capacitance is too big, a startup problem might arise. For every
channel of output, provided the safe and reliable operation is ensured, the greatest capacitance of its filter capacitor sees the external capacitor table. To
get an extremely low ripple, an LC filtering network may be connected to the input and output ends of the DC/DC converter, which may produce a more
significant filtering effect. It should also be noted that the inductance and the frequency of the LC filtering network should be staggered with the DC/DC
frequency to avoid mutual interference (see figure 1).
Requirement On Output Load
To ensure this module can operate efficiently and reliably, a minimum load is specified for this kind of DC/DC converter in addition to a maximum load
(namely full load). During operation, make sure the specified range of input voltage is not exceeded, the minimum output load is not less than 10% of the
full load, and that this product should never be operated under no load! If the actual output power is very small, please connect a resistor with proper
resistance at the output end in parallel to increase the load.
C
8
Overload Protection
Under normal operating conditions, the
C
output circuit of these products has no
protection against over-current and short-
circuits. The simplest method is to connect
a self-recovery fuse in series at the input
end or add a circuit breaker to the circuit.
External Capacitor Table
Output Voltage Regulation and
Over-voltage Protection Circuit
The simplest device for output voltage
Vin
5VDC
External
Capacitor
4.7uF
Vout
5VDC
External
Capacitor
10uF
regulation, over-voltage and over-current
protection is a linear voltage regulator with
overheat protection that is connected to the
input or output end in series (see Figure 2).
12VDC
24VDC
-
2.2uF
1uF
-
9VDC
12VDC
15VDC
4.7uF
2.2uF
1uF
TO ORDER CALL 1-888-9-AIMTEC
Share Link: 