ADN4666ARZ Ver la hoja de datos (PDF) - Analog Devices
Número de pieza
componentes Descripción
Fabricante
ADN4666ARZ Datasheet PDF : 12 Pages
| |||
ADN4666
SPECIFICATIONS
VCC = 3.0 V to 3.6 V, CL = 15 pF to GND, all specifications TMIN to TMAX, unless otherwise noted.1, 2
Table 1.
Parameter
Symbol Min Typ
LVDS INPUTS (RINx+, RINx−)
Differential Input High Threshold at RINx+, RINx−3 VTH
20
Max Unit
100 mV
Test Conditions/Comments
VCM = 1.2 V, 0.05 V, 2.95 V
Differential Input Low Threshold at RINx+, RINx−3 VTL
Common-Mode Voltage Range at RINx+, RINx−4 VCMR
Input Current at RINx+, RINx−
IIN
Input High Voltage
VIH
Input Low Voltage
VIL
Input Current
IIN
Input Clamp Voltage
VCL
OUTPUTS (ROUTx)
Output High Voltage
VOH
Output Low Voltage
VOL
Output Short-Circuit Current5
IOS
Output Off State Current
IOZ
POWER SUPPLY
No Load Supply, Current Receivers Enabled ICC
No Load Supply, Current Receivers Disabled ICCZ
ESD PROTECTION
RINx+, RINx− Pins
All Pins Except RINx+, RINx−
−100 −20
mV
0.1
2.3 V
−10 ±5
+10 μA
−10 ±1
+10 μA
−20 ±1
+20 μA
2.0
VCC
V
GND
0.8 V
−10 ±1
+10 μA
−1.5 −0.8
V
2.7 3.0
2.7 3.0
2.7 3.0
0.1
−15 −48
−10 ±1
V
V
V
0.25 V
−120 mA
+10 μA
10
15
mA
3
5
mA
±8
kV
±15
kV
±4
kV
VCM = 1.2 V, 0.05 V, 2.95 V
VID = 200 mV p-p
VIN = 2.8 V, VCC = 3.6 V or 0 V
VIN = 0 V, VCC = 3.6 V or 0 V
VIN = 3.6 V, VCC = 0 V
VIN = 0 V or VCC, other input = VCC or GND
ICL = −18 mA
IOH = −0.4 mA, VID = 200 mV
IOH = −0.4 mA, input terminated
IOH = −0.4 mA, input shorted
IOL = 2 mA, VID = −200 mV
Outputs enabled, VOUT = 0 V
Outputs disabled, VOUT = 0 V or VCC
EN and EN = VCC or GND, inputs open
EN = GND and EN = VCC, inputs open
IEC 61000-4-2 contact discharge
Human body model
Human body model
1 Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground, unless otherwise specified.
2 All typical values are given for VCC = 3.3 V and TA = 25°C.
3 VCC is always higher than the RINx+ and RINx− voltage. RINx− and RINx+ have a voltage range of −0.2 V to VCC − VID/2. However, to be compliant with ac specifications, the
common-mode voltage range is 0.1 V to 2.3 V.
4 VCMR is reduced for larger input differential voltage (VID). For example, if VID is 400 mV, VCMR is 0.2 V to 2.2 V. The fail-safe condition with inputs shorted is not supported
over the common-mode range of 0 V to 2.4 V, but is supported only with inputs shorted and no external common-mode voltage applied. VID up to VCC − 0 V can be
applied to the RINx+/RINx− inputs with the common-mode voltage set to VCC/2. Propagation delay and differential pulse skew decrease when VID is increased from 200 mV to
400 mV. Skew specifications apply for 200 mV ≤ VID ≤ 800 mV over the common-mode range.
5 Output short-circuit current (IOS) is specified as magnitude only; a minus sign indicates direction only. Note that only one output should be shorted at a time; do not
exceed the maximum junction temperature specification (150°C).
Rev. 0 | Page 3 of 12
Share Link: 