ADL5365-EVALZ Ver la hoja de datos (PDF) - Analog Devices
Número de pieza
componentes Descripción
Fabricante
ADL5365-EVALZ Datasheet PDF : 24 Pages
| |||
ADL5365
Data Sheet
5 V PERFORMANCE
VS = 5 V, IS = 95 mA, TA = 25°C, fRF = 1900 MHz, fLO = 1697 MHz, LO power = 0 dBm, VGS0 = VGS1 = 0 V, and ZO = 50 Ω, unless
otherwise noted.
Table 3.
Parameter
Test Conditions\Comments
Min Typ Max Unit
DYNAMIC PERFORMANCE
Power Conversion Loss
Including 1:1 IF port transformer and printed circuit board (PCB) loss 6.5 7.3 8.4 dB
Voltage Conversion Loss
ZSOURCE = 50 Ω, differential ZLOAD = 50 Ω differential
dB
SSB Noise Figure
8.3
dB
SSB Noise Figure Under Blocking
5 dBm blocker present ±10 MHz from wanted RF input,
LO source filtered
18.5
dB
Input Third-Order Intercept (IIP3)
fRF1 = 1899.5 MHz, fRF2 = 1900.5 MHz, fLO = 1697 MHz, each RF tone
at 0 dBm
27 36
dBm
Input Second-Order Intercept (IIP2)
fRF1 = 1950 MHz, fRF2 = 1900 MHz, fLO = 1697 MHz, each RF tone
67
dBm
at 0 dBm
Input 1 dB Compression Point (IP1dB)1 Exceeding 20 dBm RF power results in damage to the device
25
dBm
LO to IF Leakage
Unfiltered IF output
−18
dBm
LO to RF Leakage
−33
dBm
RF to IF Isolation
−50
dBc
IF/2 Spurious
0 dBm input power
−65
dBc
IF/3 Spurious
0 dBm input power
−71
dBc
POWER SUPPLY
Positive Supply Voltage
4.5 5
5.5 V
Quiescent Current
Resistor programmable
95
mA
1 Exceeding 20 dBm RF power results in damage to the device.
3.3 V PERFORMANCE
VS = 3.3 V, IS = 56 mA, TA = 25°C, fRF = 1900 MHz, fLO = 1697 MHz, LO power = 0 dBm, R9 = 226 Ω, VGS0 = VGS1 = 0 V, and ZO = 50 Ω,
unless otherwise noted.
Table 4.
Parameter
DYNAMIC PERFORMANCE
Power Conversion Loss
Voltage Conversion Loss
SSB Noise Figure
Input Third-Order Intercept (IIP3)
Input Second-Order Intercept (IIP2)
POWER INTERFACE
Supply Voltage
Quiescent Current
Power-Down Current
Test Conditions/Comments
Min Typ Max Unit
Including 1:1 IF port transformer and PCB loss
7.4
ZSOURCE = 50 Ω, differential ZLOAD = 50 Ω differential
7.1
8.4
fRF1 = 1899.5 MHz, fRF2 = 1900.5 MHz, fLO = 1697 MHz, each RF
32
tone at 0 dBm
fRF1 = 1950 MHz, fRF2 = 1900 MHz, fLO = 1697 MHz, each RF
58
tone at 0 dBm
dB
dB
dB
dBm
dBm
Resistor programmable
Device disabled
3.0 3.3 3.6 V
56
mA
150
µA
Rev. C | Page 4 of 24
Share Link: 