IAM-91563-BLK Ver la hoja de datos (PDF) - HP => Agilent Technologies

Número de pieza

componentes Descripción

Fabricante

IAM-91563-BLK

0.8– 6 GHz 3V Downconverter

HP => Agilent Technologies 

IAM-91563 Absolute Maximum Ratings

Symbol Parameter

Absolute

Units Maximum[1]

Vd

VRF, VLO

Pin

Tch

TSTG

Device Voltage, RF output to ground

RF voltage or LO voltage to ground

CW RF Input Power

Channel Temperature

Storage Temperature

V

V

dBm

°C

°C

6.0

+0.5, -1.0

+13

150

-65 to 150

Thermal Resistance[2]:

θch-c = 310°C/W

Notes:

1. Permanent damage may occur if

any of these limits are exceeded.

2. TC = 25°C (TC is defined to be the

temperature at the package pins

where contact is made to the

circuit board).

IAM-91563 Electrical Specifications, TC = 25°C, Vd = 3 V

Symbol

Parameters and Test Conditions

Units Min. Typ. Max. Std Dev[2]

Gtest Gain in test circuit[1]

RF=1890 GHz, IF=250 MHz dB 4.0 9.0

NFtest Noise Figure in test circuit[1]

RF=1890 GHz, IF=250 MHz dB

8.5 11.0

Id

Device Current

mA 6.0 9.0 12.0

NF

Noise Figure (RF & IF with external matching,

f = 0.9 GHz dB

7.0

IF=250 MHz, LO power=-5 dBm)

f = 1.9 GHz

8.5

0.5

f = 2.4 GHz

11.0

f = 4.0 GHz

16.5

f = 6.0 GHz

18.0

Gc

Conversion gain (RF and IF with external matching, f = 0.9 GHz dB

11.0

IF=250 MHz, LO power=-5 dBm)

f = 1.9 GHz

9.0

1.5

f = 2.4 GHz

7.7

f = 4.0 GHz

4.6

f = 6.0 GHz

1.7

P1 dB Output power @ 1 dB compression (RF and IF with f = 0.9 GHz dBm

-6.7

external matching, IF=250 MHz, LO power =-5 dBm) f = 1.9 GHz

-8.0

1.3

f = 2.4 GHz

-8.7

f = 4.0 GHz

-15.0

f = 6.0 GHz

-17.8

RLRF RF port return loss

f = 0.5 - 6.0 GHz dB

-1.7

0.2

RLLO LO port return loss

f = 0.5 - 6.0 GHz dB

-9.4

0.3

RLIF IF port return loss

f = 50 - 700 MHz dB

-3.7

0.2

IP3

Input Third Order Intercept Point

RF = 1.9 GHz, IF = 250 MHz dBm

-6.0

1.3

Id = 9.0 mA, LO power = -5 dBm

IP3

Input Third Order Intercept Point

RF = 1.9 GHz, IF = 250 MHz dBm

0

1.1

Id = 15 mA, LO power = -2 dBm

ISOLL-R LO-RF Isolation

RF = 1.9 GHz dB

18

ISOLR-I RF-IF Isolation (No Match)

dB

2

ISOLL-I LO-IF Isolation (No Match)

dB

4

Notes:

1. Guaranteed specifications are 100% tested in the circuit in Figure 18 in the Applications Information section.

2. Standard deviation number is based on measurement of at least 500 parts from three non-consecutive wafer lots during

the initial characterization of this product, and is intended to be used as an estimate for distribution of the typical

specification.

7-136

Share Link: