100ELT22M Ver la hoja de datos (PDF) - Fairchild Semiconductor
Número de pieza
componentes Descripción
Fabricante
100ELT22M Datasheet PDF : 5 Pages
| |||
Absolute Maximum Ratings(Note 1)
Supply Voltage (VCC)
Input Voltage (VI) VI ≤ VCC
DC Output Current (IOUT)
Continuous
Surge
Storage Temperature (TSTG)
0.0V to +7.0V
0.0V to + 7.0V
50 mA
100 mA
−65°C to + 150°C
Recommended Operating
Conditions
Power Supply Operating
TTL Input Voltage
Free Air Operating Temperature (TA)
VCC = 4.2V to 5.5V
0.0V to VCC
−40°C to +85°C
Note 1: The “Absolute Maximum Ratings” are those values beyond which
the safety of the device cannot be guaranteed. The device should not be
operated at these limits. The parametric values defined in the Electrical
Characteristics tables are not guaranteed at the absolute maximum rating.
The “Recommended Operating Conditions” table will define the conditions
for actual device operation.
PECL DC Electrical Characteristics VCC = 5.0V; GND = 0.0V (Note 2)
Symbol
Parameter
−40°C
25°C
85°C
Units
Min Typ Max Min Typ Max Min Typ Max
ICC
Power Supply Current
30
30
30
mA
VOH
Output HIGH Voltage (Note 3)
3915 3995 4120 3975 4045 4120 3975 4050 4120 mV
VOL
Output LOW Voltage (Note 3)
3170 3305 3445 3190 3295 3380 3190 3295 3380 mV
Note 2: Output parameters vary 1 to 1 with VCC. VCC can vary +0.5V/−0.8V.
Note 3: Outputs are terminated through a 50Ω Resistor to VCC − 2.0V.
Note: Devices are designed to meet the DC specifications after thermal equilibrium has been established. Circuit is tested with air flow greater than
500LFPM maintained.
TTL DC Electrical Characteristics VCC = 5.0V; GND = 0.0V (Note 4); TA = −40°C to +85°C
Symbol
IIH
Input HIGH Current
Parameter
IIL
Input LOW Current
VIK
Clamp Diode Voltage
VIH
Input HIGH Voltage
VIL
Input LOW Voltage
Note 4: VCC can vary +0.5V/−0.8V.
Min
Typ
Max Units
Condition
20
µA VIN = 2.7V
100
VIN = VCC
−200
µA VIN = 0.5V
−1.2
V IIN = −18 mA
2.0
V
0.8
V
AC Electrical Characteristics VCC = 5.0V; GND = 0.0V (Note 5)
Symbol
Parameter
−40°C
25°C
85°C
Figure
Units
Min Typ Max Min Typ Max Min Typ Max
Number
fMAX
Maximum Input Frequency
TBD
TBD
TBD
MHz
tJITTER
Cycle-to-Cycle Jitter
TBD
TBD
TBD
ps
tPLH, tPHL Propagation Delay to Output (Note 6) 100
600 100
600 100
600 ps Figure 1
tr, tf
Output Rise Time/Fall Times
200
(20% to 80%)
500 200
500 200
500 ns Figure 2
tskpp
Part to Part Skew
500
500
500 ps
tskew
Within Device Skew (Note 7)
100
100
100 ps
Note 5: VCC can vary +0.5V/−0.8V.
Note 6: Specifications for standard TTL input signal (see Figure 1).
Note 7: Within-device skew is defined as identical transitions on similar paths through a device.
www.fairchildsemi.com
2
Share Link: 