PV36X200C01 Ver la hoja de datos (PDF) - Murata Manufacturing
Número de pieza
componentes Descripción
Fabricante
PV36X200C01 Datasheet PDF : 55 Pages
| |||
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
PVZ2/PVA2 Series Notice
Continued from the preceding page.
c Soldering Profile
Reflow Soldering Profile
1. Soldering profile for lead free solder (96.5Sn/3.0Ag/0.5Cu)
T5
T3
T4
T2
T1
t2
Limit Profile
t3
Standard Profile
R50E.pdf
Jul.23,2012
1
t1
Time (s)
Series
PVZ2
PVA2
Standard Profile
Limit Profile
Pre-heating
Heating
Peak
Temperature
Cycle of
Pre-heating
Heating
Peak
Temperature
Cycle of
Temp. (T1) Time (t1) Temp. (T2) Time (t2)
(T3)
Reflow Temp. (T1) Time (t1) Temp. (T4) Time (t3)
(T5)
Reflow
°C
sec.
°C
sec.
°C
Time
°C
sec.
°C
sec.
°C
Time
150 to 180 60 to 120 220 30 to 60 245±3
2 150 to 180 60 to 120 220 30 to 60 260
2
150 to 180 60 to 120 220 30 to 60 245±3
2 150 to 180 60 to 120 220 30 to 60 260 +5/-0 2
2. Soldering profile for Eutectic solder (63Sn/37Pb)
(Limit profile: refer to 1)
T3
Standard Profile
T2
Series
Pre-heating
Heating
Peak
Temperature
Cycle of
Temp. (T1) Time (t1) Temp. (T2) Time (t2)
(T3)
Reflow
T1
t2
Standard Profile
°C
sec.
°C
sec.
°C
Time
PVZ2
PVA2
150 60 to 120 183
30
230
1
t1
time (s)
Soldering Iron
Series
PVZ2
PVA2
Temperature of Soldering Iron Tip
°C
350±10
Standard Condition
Soldering Time
Soldering Iron Power Output
sec.
W
3 max.
30 max.
Cycle of Soldering Iron
Time
1
c Notice (Handling)
1. Use suitable screwdrivers that fit comfortably in the
driver slot. We recommend the screwdriver below.
* Recommended screwdriver for manual adjustment
Murata P/N: KMDR190
2. The screwdriver should be set in the products
vertically, do not apply more than 4.9N (Ref. 500gf)
of twist and stress after mounting onto PCB to
prevent contact intermittence. If excessive force is
applied, the trimmer potentiometer may not function.
3. Please use within the effective rotational angle.
The trimmer potentiometer does not have a
mechanical stop for over rotation. In cases out of
effective rotational angle, the trimmer
potentiometer may not function.
4. When using a lock paint to fix the slot position or
cover the rotor, please evaluate performance with
your product. Lock paint may cause corrosion or
electrical contact problems.
c Notice (Other)
1. Please make sure that your product has been
evaluated and confirmed against your
specifications when our product is mounted to your
product.
2. Murata cannot guarantee trimmer potentiometer
integrity when used under conditions other than
those specified in this document.
9
Share Link: 