MAX7030 Ver la hoja de datos (PDF) - Maxim Integrated

Número de pieza

componentes Descripción

Fabricante

MAX7030

Low-Cost, 315MHz, 345MHz, and 433.92MHz ASK Transceiver with Fractional-N PLL

Maxim Integrated 

Low-Cost, 315MHz, 345MHz, and 433.92MHz

ASK Transceiver with Fractional-N PLL

PIN

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21, 25

22

23

24

26

27

Pin Description

NAME

PAVDD

ROUT

TX/RX1

TX/RX2

PAOUT

AVDD

LNAIN

LNASRC

LNAOUT

MIXIN+

MIXIN-

MIXOUT

IFIN-

IFIN+

PDMIN

PDMAX

DS-

DS+

OP+

DF

N.C.

T/R

ENABLE

DATA

DVDD

HVIN

FUNCTION

Power-Amplifier Supply Voltage. Bypass to GND with 0.01µF and 220pF capacitors placed as close

as possible to the pin.

Envelope-Shaping Output. ROUT controls the power-amplifier envelope’s rise and fall times. Connect

ROUT to the PA pullup inductor or optional power-adjust resistor. Bypass the inductor to GND as

close as possible to the inductor with 680pF and 220pF capacitors, as shown in the Typical

Application Circuit.

Transmit/Receive Switch Throw. Drive T/R high to short TX/RX1 to TX/RX2. Drive T/R low to disconnect

TX/RX1 from TX/RX2. Functionally identical to TX/RX2.

Transmit/Receive Switch Pole. Typically connected to ground. See the Typical Application Circuit.

Power-Amplifier Output. Requires a pullup inductor to the supply voltage (or ROUT if envelope

shaping is desired), which can be part of the output-matching network to an antenna.

Analog Power-Supply Voltage. AVDD is connected to an on-chip +3.0V regulator in 5V operation.

Bypass AVDD to GND with a 0.1µF and 220pF capacitor placed as close as possible to the pin.

Low-Noise Amplifier Input. Must be AC-coupled.

Low-Noise Amplifier Source for External Inductive Degeneration. Connect an inductor to GND to set

the LNA input impedance.

Low-Noise Amplifier Output. Must be connected to AVDD through a parallel LC tank filter. AC-couple

to MIXIN+.

Noninverting Mixer Input. Must be AC-coupled to the LNA output.

Inverting Mixer Input. Bypass to AVDD with a capacitor as close as possible to the LNA LC tank filter.

330Ω Mixer Output. Connect to the input of the 10.7MHz filter.

Inverting 330Ω IF Limiter-Amplifier Input. Bypass to GND with a capacitor.

Noninverting 330Ω IF Limiter-Amplifier Input. Connect to the output of the 10.7MHz IF filter.

Minimum-Level Peak Detector for Demodulator Output

Maximum-Level Peak Detector for Demodulator Output

Inverting Data Slicer Input

Noninverting Data Slicer Input

Noninverting Op-Amp Input for the Sallen-Key Data Filter

Data-Filter Feedback Node. Input for the feedback capacitor of the Sallen-Key data filter.

No Connection. Do not connect to this pin.

Transmit/Receive. Drive high to put the device in transmit mode. Drive low or leave unconnected to

put the device in receive mode. It is internally pulled down.

Enable. Drive high for normal operation. Drive low or leave unconnected to put the device into shut-

down mode.

Receiver Data Output/Transmitter Data Input

Digital Power-Supply Voltage. Bypass to GND with a 0.01µF and 220pF capacitor placed as close as

possible to the pin.

High-Voltage Supply Input. For 3V operation, connect HVIN to AVDD, DVDD, and PAVDD. For 5V

operation, connect only HVIN to 5V. Bypass HVIN to GND with a 0.01µF and 220pF capacitor placed

as close as possible to the pin.

______________________________________________________________________________________ 11

Share Link: