MAX5432LETA Ver la hoja de datos (PDF) - Maxim Integrated

Número de pieza

componentes Descripción

Fabricante

MAX5432LETA

32-Tap, Nonvolatile, I2C, Linear, Digital Potentiometers

Maxim Integrated 

32-Tap, Nonvolatile, I2C, Linear, Digital

Potentiometers

SDA

tSU-DAT

tLOW

tHD-DAT

tSU-STA

tHD-STA

tR

tF

tBUF

tSU-STO

SCL

tHD-STA

tHIGH

tR

tF

S

PARAMETERS ARE MEASURED FROM 30% TO 70%.

Figure 1. I2C Serial-Interface Timing Diagram

Sr

A

P

S

high while SCL is high. The bus is then free for another

transmission (Figure 3).

Bit Transfer

One data bit is transferred during each clock pulse.

The data on the SDA line must remain stable while SCL

is high (Figure 5).

Acknowledge

The acknowledge bit is a clocked 9th bit that the recip-

ient uses to handshake receipt of each byte of data

(Figure 6). Each byte transferred effectively requires 9

bits. The master generates the 9th clock pulse, and the

recipient pulls down SDA during the acknowledge

clock pulse, so the SDA line is stable low during the

high period of the clock pulse. When the master trans-

mits to the MAX5432–MAX5435, the devices generate

the acknowledge bit because the MAX5432–MAX5435

are the recipients.

Slave Address

The MAX5432–MAX5435 have a 7-bit-long slave

address (Figure 4). The 8th bit following the 7-bit slave

address is the NOP/W bit. Set the NOP/W bit low for a

write command and high for a no-operation command.

Table 1a shows four possible slave addresses for the

MAX5432/MAX5433 and Table 1b shows four possible

slave addresses for the MAX5434/MAX5435. The first 4

bits (MSBs) of the slave addresses are always 0101.

Bits A2 and A1 are factory programmed for the

MAX5432/MAX5433 (Table 1a). Connect the A0 input

(MAX5432/MAX5433 only) to either GND or VDD to

select one of two I2C device addresses. Each device

must have a unique address to share the bus. A maxi-

mum of four MAX5432/MAX5433 devices can share the

same bus. Bits A2, A1, and A0 are factory programmed

for the MAX5434/MAX5435 (Table 1b).

Table 1a. Address Codes

(MAX5432/MAX5433 Only)

PART

ADDRESS BYTE

SUFFIX A6 A5 A4 A3 A2 A1 A0

NOP/W

L

0 1 0 1 0 0 0 NOP/W

L

0 1 0 1 0 0 1 NOP/W

M

0 1 0 1 1 0 0 NOP/W

M

0 1 0 1 1 0 1 NOP/W

Table 1b. Address Codes

(MAX5434/MAX5435 Only)

PART

ADDRESS BYTE

SUFFIX A6 A5 A4 A3 A2 A1 A0

NOP/W

L

0 1 0 1 0 0 0 NOP/W

M

0 1 0 1 1 0 0 NOP/W

N

0 1 0 1 0 1 0 NOP/W

P

0 1 0 1 1 1 0 NOP/W

Message Format for Writing

A write to the MAX5432–MAX5435 consists of the trans-

mission of the device’s slave address with the 8th bit set

to zero, followed by at least 1 byte of information. The

1st byte of information is the command byte. The bytes

received after the command byte are the data bytes.

The 1st data byte goes into the internal register of the

MAX5432–MAX5435 as selected by the command byte

(Figure 8).

__________________________________________________________________________

Share Link: