MAX3108 Ver la hoja de datos (PDF) - Maxim Integrated
Número de pieza
componentes Descripción
Fabricante
MAX3108 Datasheet PDF : 56 Pages
| |||
MAX3108
SPI/I2C UART with 128-Word FIFOs in WLP
ABSOLUTE MAXIMUM RATINGS
(Voltages referenced to AGND.)
VL, VCC, VEXT, XIN................................................-0.3V to +4.0V
XOUT......................................................... -0.3V to (VCC + 0.3V)
V18....................... -0.3V to the lesser of (VCC + 0.3V) and 2.0V
RST, IRQ, MOSI/A1, CS/A0, SCLK/SCL,
MISO/SDA, LDOEN, SPI/I2C..................... -0.3V to (VL + 0.3V)
TX, RX, RTS, CTS, GPIO_........................ -0.3V to (VEXT + 0.3V)
DGND....................................................................-0.3V to +0.3V
Continuous Power Dissipation (TA = +70NC)
WLP (derate 19.2mW/NC above +70NC).................... 1536mW
Operating Temperature Range........................... -40NC to +85NC
Maximum Junction Temperature......................................+150NC
Storage Temperature Range............................. -65NC to +150NC
Soldering Temperature (reflow).......................................+260NC
PACKAGE THERMAL CHARACTERISTICS (Note 1)
WLP
Junction-to-Ambient Thermal Resistance (BJA)............52NC/W
Junction-to-Case Thermal Resistance (BJC).................11NC/W
Note 1: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-layer
board. For detailed information on package thermal considerations, refer to www.maximintegrated.com/thermal-tutorial.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
DC ELECTRICAL CHARACTERISTICS
(VCC = 1.71V to 3.6V, VL = 1.71V to 3.6V, VEXT = 1.71V to 3.6V, TA = -40NC to +85NC, unless otherwise noted. Typical values are at
VCC = 2.8V, VL = 1.8V, VEXT = 2.5V, TA = +25NC.) (Notes 2, 3)
PARAMETER
Digital Interface Supply Voltage
Analog Supply Voltage
UART Interface Logic Supply
Voltage
Logic Supply Voltage
CURRENT CONSUMPTION
SYMBOL
VL
VCC
CONDITIONS
Internal PLL disabled and bypassed
Internal PLL enabled
VEXT
V18
MIN TYP MAX UNITS
1.71
3.6
V
1.71
3.6
V
2.35
3.6
1.71
3.6
V
1.65
1.95
V
VCC Supply Current
1.8MHz crystal oscillator active, PLL
disabled, SPI/I2C interface idle, UART
interfaces idle, LDOEN = high
ICC
Baud rate = 1Mbps, 20MHz external clock,
SPI/I2C interface idle, PLL disabled, UART
in loopback mode, LDOEN = low
500
FA
500
VCC Shutdown Supply Current
ICCSHDN Shutdown mode, LDOEN = low, RST = low,
all inputs and outputs are idle
35
FA
VL Shutdown or Sleep Supply
Current
IL
Shutdown or sleep mode, all inputs and
outputs are idle
15
FA
VEXT Shutdown Supply Current
V18 Input Power-Supply Current
in Shutdown Mode
IEXT
I18SHDN
Shutdown mode, RST = low, all inputs and
outputs are idle
Shutdown mode, LDOEN = low, RST = low,
all inputs and outputs are idle
10
FA
50
FA
6
Maxim Integrated
Share Link: 