MAX14535E Ver la hoja de datos (PDF) - Maxim Integrated
Número de pieza
componentes Descripción
Fabricante
MAX14535E Datasheet PDF : 13 Pages
| |||
Low-Resistance DPDT Switches
with Negative Rail
ABSOLUTE MAXIMUM RATINGS
(Voltages referenced to GND.)
VCC, CB, EN ..........................................................-0.3V to +6.0V
NO_, NC_, COM_ (VCC > 2.4V, MAX14535E/
MAX14536E/MAX14539E).................................-1.8V to +3.6V
NO_, NC_, COM_ (VCC < 2.4V, MAX14535E/
MAX14536E/MAX14539E).................................-0.3V to +3.6V
NO_, NC_, COM_ (VEN < VIL, MAX14537E/
MAX14538E)......................................................-0.3V to +6.0V
NO_, NC_, COM_ (VEN > VIL, VCC > 2.4V,
MAX14537E/MAX14538E).................................-1.8V to +3.6V
NO_, NC_, COM_ (VEN < VIL, VCC < 2.4V,
MAX14537E/MAX14538E).................................-0.3V to +3.6V
Continuous Current into NO_, NC_, COM_ Terminals....±300mA
Peak Current into NO_, NC_,
COM_ Terminals (50% duty cycle).............................±500mA
Continuous Power Dissipation (TA = +70°C)
10-Pin UTQFN (derate 6.9mW/°C above +70°C).........559mW
Junction-to-Ambient Thermal Resistance (θJA) (Note 1)..143.1°C/W
Junction-to-Case Thermal Resistance (θJC) (Note 1)...20.1°C/W
Operating Temperature Range ...........................-40°C to +85°C
Storage Temperature Range .............................-65°C to +150°C
Junction Temperature Range ............................-40°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Note 1: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7 using a four-
layer board. For detailed information on package thermal considerations, refer to www.maxim-ic/thermal-tutorial.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VCC = +2.4V to +5.5V, TA = -40°C to +85°C, unless otherwise noted. Typical values are at VCC = +3.0V, TA = +25°C.) (Note 2)
PARAMETER
Power-Supply Range
Supply Current
Supply Current Increase with
Logic Level
Analog Signal Range
On-Resistance
On-Resistance Match Between
Channels
On-Resistance Flatness
Shunt Switch Resistance
SYMBOL
VCC
ICC
CONDITIONS
VCC =
3.0V
MAX14537E/MAX14538E,
VEN = 0
MAX14535E/MAX14536E/
MAX14539E, VEN = 0, VEN = VCC
VCC =
5.5V
MAX14537E/MAX14538E,
VEN = 0
MAX14535E/MAX14536E/
MAX14539E, VEN = 0, VEN = VCC
VEN = 0.4V or 1.4V, VCB = 0.4V or 1.4V
MAX14537E/MAX14538E,
VEN < VIL
MAX14537E/MAX14538E,
VEN > VIH
MAX14535E/MAX14536E/MAX14539E
RON
∆RON
RFLAT(ON)
RSH
VCC = 3.0V, VCOM_ = -1.5V, 3.0V;
INO_ = 100mA or INC_ = 100mA
VCC = 3.0V, VCOM_ = 0; ICOM_ = 100mA
(Note 3)
VCC = 3.0V, ICOM_ = 100mA;
VCOM_ = -1.5V to +3.0V (Note 4)
INO_ or INC_ = 1mA
MIN TYP MAX UNITS
2.4
5.5
V
1
8
15
µA
1
12
25
5
µA
0
VCC
Min
-1.5
(3.0V,
V
VCC)
Min
-1.5
(3.0V,
VCC)
0.135 0.35
Ω
0.05
Ω
0.3
1
mΩ
500 1000
Ω
2 _______________________________________________________________________________________
Share Link: 