AWC6312RM9P9 Ver la hoja de datos (PDF) - ANADIGICS
Número de pieza
componentes Descripción
Fabricante
AWC6312RM9P9 Datasheet PDF : 8 Pages
| |||
AWC6312R
Table 4: Electrical Specifications - CDMA Operation
(TC = +25 °C, VBATT = VCC = +3.4 V, VEN = +2.4 V, 50 Ω system, IS-95 uplink waveform)
PARAMETER
MIN TYP MAX UNIT COMMENTS
Gain
25
27
29
12 13.5 16
dB
POUT = +28 dBm, VMODE1 = 0 V
POUT = +16 dBm, VMODE1 = +2.4 V
Adjacent Channel Power
at +1.25 MHz offset
Primary Channel BW = 1.23 MHz
-
-50 -46.5 dBc POUT = +28 dBm, VMODE1 = 0 V
Adjacent Channel BW = 30 kHz
-
-55 -47
POUT = +16 dBm, VMODE1 = +2.4 V
Adjacent Channel Power
at + 1.98 MHz offset
Primary Channel BW = 1.23 MHz
Adjacent Channel BW = 30 kHz
-
-
-58
-59
-54
-54
dBc
POUT = +28 dBm, VMODE1 = 0 V
POUT = +16 dBm, VMODE1 = +2.4 V
Alternate Channel Power
at +2.25 MHz offset
Primary Channel BW = 1.23 MHz
Adjacent Channel BW = 30 kHz
-
-
-61 -57
-62 -57
dBc
POUT = +28 dBm, VMODE1 = 0 V
POUT = +16 dBm, VMODE1 = +2.4 V
Power-Added Efficiency
37
40
-
20
23
-
%
POUT = +28 dBm, VMODE1 = 0 V
POUT = +16 dBm, VMODE1 = +2.4 V
Quiescent Current (Icq)
-
8
13
mA through VCC pin, VMODE1 = +2.4 V
Enable Current
-
0.3 0.8
mA through VEN pin, PA "on"
Mode Control Current
-
0.3 0.8
mA through VMODE pin, VMODE1 = +2.4 V
Battery Current
-
2.5
5
mA through VBATT pin, VMODE1 = +2.4 V
Leakage Current
-
<1
5
µA
VCC = +4.2 V, VEN = 0 V,
VMODE1 = 0 V
-
-135 -133 dBm/Hz 1930 MHz to 1990 MHz, POUT <
28dBm
Noise in Receive Band
-
-138 -135 dBm/Hz 1930 MHz to 1990 MHz, POUT <
16 dBm
-
-142
- dBm/Hz 1575 + 1.023 MHz
Harmonics
2fo
3fo, 4fo
-
-
-41 -30
-55 -35
CW Measurement
dBc VMODE1 = 0V
Input Impedance
-
-
2:1 VSWR
Spurious Output Level
(all spurious outputs)
POUT < +28 dBm
-
-
-65
dBc
In-band load VSWR < 5:1
Out-of-band load VSWR < 10:1
Applies over all operating ranges
Load mismatch stress with no
permanent degradation or failure
8:1
-
-
Notes:
1. ACPRs and Efficiency Limits at 1882.5 MHz only.
VSWR Applies over full operating range
4
Data Sheet - Rev 2.0
01/2009
Share Link: 