ACAS0612AT Ver la hoja de datos (PDF) - Vishay Semiconductors
Número de pieza
componentes Descripción
Fabricante
ACAS0612AT Datasheet PDF : 6 Pages
| |||
ACAS 0612 AT - Precision Automotive
Automotive Precision Thin Film Chip Resistor Array Vishay Beyschlag
All products comply with the GADSL (1) and the
CEFIC-EECA-EICTA (2) list of legal restrictions on
hazardous substances. This includes full compliance with
the following directives:
• 2000/53/EC End of Vehicle life Directive (ELV) and
Annex II (ELV II)
• 2002/95/EC Restriction of the use of Hazardous
Substances directive (RoHS)
• 2002/96/EC Waste Electrical and Electronic Equipment
Directive (WEEE)
APPROVALS
Where applicable, the resistors are tested in accordance with
EN 140401-801 which refers to EN 60115-1 and EN 140400.
Furthermore, the chip resistor array is qualified according to
AEC-Q200.
Notes
(1) Global Automotive Declarable Substance List, see www.gadsl.org
(2) CEFIC (European Chemical Industry Council), EECA (European Electronic Component Manufacturers Association), EICTA (European trade
organisation representing the information and communications technology and consumer electronics), see www.eicta.org → issues →
environment policy → chemicals → chemicals for electronics
• The quoted IEC standards marked with an asterisk (*) are also released as EN standards with the same number and identical contents
TESTS AND REQUIREMENTS
Essentially all tests are carried out in accordance with the
following specifications:
EN 60115-1, Generic specification (includes tests)
EN 140400, Sectional specification (includes schedule for
qualification approval)
The testing also covers most of the requirements specified
by EIA/IS-703 and JIS-C-5202.
The tests are carried out in accordance with IEC 60068*
and under standard atmospheric conditions according to
IEC 60068-1*, 5.3. Climatic category LCT/UCT/56 (rated
temperature range: Lower Category Temperature, Upper
Category Temperature; damp heat, long term, 56 days) is
valid.
Unless otherwise specified the following values apply:
Temperature: 15 °C to 35 °C
Relative humidity: 45 % to 75 %
Air pressure: 86 kPa to 106 kPa (860 mbar to 1060 mbar)
In the following table only the tests and requirements are
listed with reference to the relevant clauses of EN 60115-1
and IEC 60068-2*; a short description of the test procedure
is also given.
TEST PROCEDURES AND REQUIREMENTS
EN
60 115-1
CLAUSE
IEC
60 068-2*
TEST
METHOD
TEST
PROCEDURE
Stability for product types:
ACAS 0612 AT
4.5
4.8.4.2
-
Resistance
-
Temperature coefficient
Climatic category
(LCT/UCT/duration)
-
At 20/LCT/ 20 °C and
20/UCT/20 °C
4.25.1
-
Endurance
U = P70 x R
or U = Umax.;
70 °C; 1000 h
1.5 h on; 0.5 h off;
125 °C
155 °C
4.25.3
-
Endurance at upper
category temperature
125 °C; 1000 h;
155 °C; 1000 h
REQUIREMENTS (1)
PERMISSIBLE CHANGE (ΔR)
47 Ω to 150 kΩ
- 55 °C/+ 125 °C/56 days
± 0.5 %; ± 0.25 %
± 50 ppm/K; ± 25 ppm/K
± (0.1 % R + 0.01 Ω)
± (0.25 % R + 0.05 Ω)
± (0.25 % R + 0.05 Ω)
± (0.4 % R + 0.05 Ω)
Document Number: 28770
Revision: 11-Sep-08
For technical questions, contact: filmresistors.thinfilmarray@vishay.com
www.vishay.com
279
Share Link: 