AH101J Ver la hoja de datos (PDF) - Unspecified

Número de pieza

componentes Descripción

Fabricante

AH101J

CERAMIC DISC CAPACITOR SAFETY RECOGNIZED / AH SERIES

Unspecified 

POE-D10-00-E-13

SAFETY STANDARDS REGULATED, REINFORCED

INSULATION TYPE, AH SERIES

Ver: 13 Page: 10 / 18

7. Specification and test method:

7.1 Operating Temperature Range: -40 to +125°C

7.2 Test condition:

Test and measurement shall be made at the standard condition. (temperature 15~35℃, relative humidity 45~75%

and atmospheric pressure 860~1060hpa). Unless otherwise specified herein.

If doubt occurred on the value of measurement, and measurement was requested by customer capacitors shall be

measured at the reference condition. (temperature 20±2℃or25 ± 2℃, relative humidity 60~70% and atmospheric

pressure 860~1060hpa.)

7.3 Performance:

No

Items

Performance

Testing method

7.3.1

7.3.2

7.3.3

7.3.4

7.3.5

7.3.6

Appearance

And dimension

Marking

Between

terminals

Withstand

voltage

Body

Insulation

Insulation Between

Resistance terminals

Capacitance

Dissipation

Factor(tanδ) or Q

The appearance and dimension Visual check.

shall be as given in section 3.

The marking shall be easily Visual check.

legible. (As given section 5)

The capacitors shall not be damage when AC4000V

No failure.

(rms.) are applied between the lead wires for 60sec.

(Charge/Discharge current ≤ 50mA.)

First. The terminals of the capacitor shall be closely

wrapped around the body of the capacitor distance of

about 3 to 4mm from each terminal. Then, the

No failure.

capacitor shall be inserted into a container filled with

metal balls of about 1mm diameter. Finally, AC4000V

(rms.) is applied for 60sec between the capacitor lead

wires and metal balls. (Charge/Discharge current ≤

50mA.)

10000MΩ or more.

The insulation resistance shall be measured with

DC500±50V within 60±5sec of charging.

Within specified tolerance.

Y5P、Y5U：D.F.≦ 2.5%

Y5V：D.F.≦ 5.0%

CH&SL：

30pF&above:≧ 1000

Below 30PF:≧400+20×C

Y5P&Y5U&Y5V: The capacitance shall be measured

at 20±2℃ with 1kHz±20% and 5V(rms.) or less.

CH&SL: The capacitance shall be measured at 25℃

with 1MHz±20% and1.0±0.2Vrms

7.3.7

Temperature

Characteristic

Char. Capacitance Change

Y5P Within ± 10%

Y5U Within ±２５０５%

Y5V Within –80 ~ +30%

CH 0±60ppm/℃

-1000~+350

SL ppm/℃

(+20℃~+85℃)

The capacitance measurement shall be made at each

step specified in Table 1.

Table 1

Step

Temperature (℃)

1

+20±2

2

-25±2

3

+20±2

4

+85±2

5

+20±2

Pre-treatment:

Capacitor shall be stored at 85±2℃ for 1hour, then

placed at ※1room condition for 24±2hours before

measurements.

7.3.8 Solderability of Leads

Lead wire should be

The lead wire of capacitor should be dipped into

molten solder for 5 ± 0.5 sec.

soldered with uniform

coating on the axial

direction over 3/4 of the

circumferential direction.

The depth of immersion is up to about 1.5 to 2.0 mm

from the root of lead wires.

Temp. of solder：Lead Free Solder ( Sn-3Ag-0.5Cu)

245±5℃

Share Link: