M62023 Ver la hoja de datos (PDF) - MITSUBISHI ELECTRIC
Número de pieza
componentes Descripción
Fabricante
M62023 Datasheet PDF : 4 Pages
| |||
MITSUBISHI <Dig./Ana.INTERFACE>
P R E L I M I N A R Y M62023L,P,FP NSootmicee:Tphairsamisentoritcalimfinitaslasrpeescuifibcjaetciot nto.
change.
SYSTEM
RESET
IC
WITH
SWITCH
FOR
MEMORY
BACK-UP
ABSOLUTE MAXIMUM RATINGS (Ta=25°C, unless otherwise noted)
Symbol
VIN
IOUT
Pd
K
Topr
Tstg
Parameter
Input voltage
Output current
Power dissipation
Thermal derating
Operating temperature
Storage temperature
Conditions
Ta ≥ 25°C
Ratings
7
100
800(L)/625(P)/440(FP)
8(L)/6.25(P)/4.4(FP)
-20 to +75
-40 to +125
Unit
V
mA
mW
mW/°C
°C
°C
ELECTRICAL CHARACTERISTICS (Ta=25°C, unless otherwise noted)
Symbol
Parameter
Test Conditions
VS Detection voltage
∆VS Hysteresis voltage
VIN (At charge from H L)
∆VS=VSH-VSL
ICC Circuit current
IOUT=0mA
VIN=2V
VIN=3V
VDROP
Difference between
input and output voltages
VIN=3V
IOUT=50mA
IOUT=80mA
VOH(Ct) Ct output voltage (high level) VIN=3V (Note 1)
VOL(Ct) Ct output voltage (low level) VIN=2V (Note 1)
VOH(RES) RES output voltage (high level) VIN=2V (Note 1)
VOL(RES) RES output voltage (low level) VIN=3V
(Note 1)
Isink=1mA
VOH(RES) RES output voltage (high level) VIN=3V (Note 1)
VOL(RES) RES output voltage (low level) VIN=2V
(Note 1)
Isink=1mA
VIN=2V (Note 2)
VOH(CS) CS output voltage (high level)
VIN=0V, VBAT=3V (Note 2)
VOL(CS) CS output voltage (low level) VIN=3V
(Note 1)
Isink=1mA
IR
Backup Di leak current
VBAT=3V
VIN=3V
VIN=0V
VF
Backup Di forward direction voltage
IF=10µA
tpd Delay time
VIN=0V 3V, Ct=4.7µF
td Response time
VIN=3V 2V
VOPL(RES) RES limit voltage of operation (Note 3)
Limits
Min Typ Max
Unit
2.44 2.57 2.70
V
50 100 200
mV
1.5 3.0
mA
6.5 10
0.1 0.2
V
0.15 0.3
2.0 2.4
V
0.02 0.1
V
1.5 2.0
V
0.02
V
0.04 0.2
2.5 3.0
V
0.02
V
0.04 0.2
1.3 1.6
V
2.40 2.47
0.07
V
0.08 0.3
±0.5
±0.5
µA
0.54 0.6
V
10 27 55
ms
5.0 25.0
µs
0.65
V
Note 1. Regarding conditions to measure VOH and VOL, voltage values are generated by internal resistance only and no external
resistor is used.
2. These values are produced inserting an external resistor, RCS=1MΩ, between the CS pin and GND.
3. With no external resistor (10KΩ internal resistance only)
( 2 / 4)
1997.5.30- rev
Share Link: 