ASX20003 Ver la hoja de datos (PDF) - Panasonic Corporation
Número de pieza
componentes Descripción
Fabricante
ASX20003
Panasonic Corporation
ASX20003 Datasheet PDF : 4 Pages
| |||
SX (ASX)
2. Specifications
Characteristics
Contact
Rating
Electrical
characteristics
Item
Arrangement
Static contact resistance
(During initial and electric life tests)
Dynamic contact resistance
(During initial and electric life tests)
Contact material
Nominal switching capacity
Max. switching power
Max. switching voltage
Max. switching current
Min. switching capacity (Reference value)*1
Nominal operating
power
Single side stable
1 coil latching
2 coil latching
Insulation resistance (Initial)
Breakdown voltage
(Initial)
Surge breakdown
voltage (Initial)
Between open contacts
Between contact and coil
Between contact sets
Between open contacts
Between contacts and coil
Temperature rise (at 20°C 68°F)
Operate time [Set time] (at 20°C 68°F)
Release time [Reset time] (at 20°C 68°F)
Mechanical
characteristics
Expected life
Thermal
electromotive force
Shock resistance
Vibration resistance
Mechanical
Electrical
Functional
Destructive
Functional
Destructive
Conditions
Unit weight
Conditions for operation, transport and storage*2
Max. operating speed (at rated load)
Specifications
2 Form C
Max. 100 mΩ (By voltage drop of 20 mV 1 mA [1kHz])
(By nominal switching capacity: No. of operations: 107)
Max. 1 Ω (By voltage drop of 20 mV 1 mA [1 kHz], Measurement delay 10 ms after applying
nominal coil voltage) (By nominal switching capacity: No. of operations: 107)
Stationary contact: AgPd+Au clad Movable contact: AgPd
10 mA 10 V DC (resistive load)
0.1 W (resistive load)
10 V DC
10 mA DC
10 µA 1 mV DC
50mW (1.5 to 12 V DC), 70mW (24 V DC)
35mW (1.5 to 12 V DC), 50mW (24 V DC)
70mW (1.5 to 12 V DC), 150mW (24 V DC)
Min. 10,000MΩ (at 500V DC)
Measurement at same location as “Initial breakdown voltage” section.
750 Vrms for 1min. (Detection current: 10mA)
1,000 Vrms for 1min. (Detection current: 10mA)
1,000 Vrms for 1min. (Detection current: 10mA)
1,500 V (10×160µs) (FCC Part 68)
2,500 V (2×10µs) (Telcordia)
Max. 50°C
(By resistive method, nominal coil voltage applied to the coil; contact carrying current:
10mA.)
Max. 5 ms [Max. 5 ms] (Nominal coil voltage applied to the coil, excluding contact bounce
time.)
Max. 5 ms [Max. 5 ms] (Nominal coil voltage applied to the coil, excluding contact bounce
time.) (without diode)
Min. 750 m/s2 (Half-wave pulse of sine wave: 6 ms; detection time: 10µs.)
Min. 1,000 m/s2 (Half-wave pulse of sine wave: 6 ms.)
10 to 55 Hz at double amplitude of 3.3 mm (Detection time: 10µs.)
10 to 55 Hz at double amplitude of 5 mm
Min. 5 × 107 (at 750 cpm)
Min. 107 (10 mA 10 V DC resistive load) (at 750 cpm)
Max. 3µV (at nominal voltage applied to the coil)
Ambient temperature: –40°C to +70°C –40°F to +158°F
Humidity: 5 to 85% R.H. (Not freezing and condensing at low temperature)
750 cpm
Approx. 2 g .071 oz
Notes: *1 This value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the
actual load.
*2 Refer to 6. Conditions for operation, transport and storage mentioned in AMBIENT ENVIRONMENT.
REFERENCE DATA
1. Switching capacity range
10mA
10µA
1mV
10V
Contact voltage
2-(1). Change in dynamic contact resistance
(10 mA 10 V DC resistive load)
Tested sample: ASX20012, 10 pcs.
Operating speed: 750 cpm
Measured condition: 10 ms after applying nominal coil
voltage, using voltage drop of 20 mV, 1 mA, 1 kHz.
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
0
Max.
Min.
1,000
No. of operations, × 104
2-(2). Change in dynamic contact resistance
(10 µA 1 mV DC resistive load)
Tested sample: ASX20012, 10 pcs.
Operating speed: 750 cpm
Measured condition: 10 ms after applying nominal coil
voltage, using voltage drop of 20 mV, 1 mA, 1 kHz.
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
0
Max.
Min.
1,000
2,000
No. of operations, × 104
All Rights Reserved © COPYRIGHT Panasonic Electric Works Co., Ltd.
Share Link: