6N137 Ver la hoja de datos (PDF) - Sharp Electronics
Número de pieza
componentes Descripción
Fabricante
6N137 Datasheet PDF : 5 Pages
| |||
6N137
s Electro-optical Characteristics
( Ta = 0 to + 70˚C unless otherwise specified )
Parameter
Logic ( 1) output current
Logic ( 0) output voltage
Logic ( 1) enable current
Logic ( 0) enable current
Logic ( 1) supply current
Logic ( 0) supply current
*1Leak current
*1Isolation resistance ( input-output )
*1Capacitance ( input-output )
*2Input forward voltage
Input reverse voltage
Input capacitance
*3Current transfer ratio
*4Propagation delay time
Output ( 0) → (1)
*5Propagation delay time
Output (1) → ( 0)
Output rise-fall time ( 10 to 90% )
*6Enable propagation
delay time (1) → ( 0)
*7Enable propagation
delay time ( 0) → (1)
*8Instantaneous common mode
rejection voltage “ Output ( 0) ”
*8Instantaneous common mode
rejection voltage “ Output (1) ”
Symbol
I OH
V OL
I EH
I EL
I CCH
I CCL
I I-O
R I-O
CI-O
VF
BV R
C IN
CTR
Conditions
VCC = 5.5V, V O = 5.5V, I F = 250 µA, VE = 2.0V
VCC = 5.5V, I F = 5mA, V EH = 2.0V, I OL (Sinking ) = 13mA
VCC = 5.5V, V E = 2.0V
VCC = 5.5V, V E = 0.5V
VCC = 5.5V, I F = 0mA, VE = 0.5V
VCC = 5.5V, I F = 10mA, VE = 0.5V
45% RH, Ta = 25˚C, t = 5s, V I-O = 3 000V dc
VI-O = 500V, Ta = 25˚C
f = 1MHz, Ta = 25˚C
IF = 10mA, Ta = 25˚C
IR = 10 m A, Ta = 25˚C
VF = 0, f = 1MHz
IF = 5.0mA, R L = 100Ω
t PLH Ta = 25˚C, V CC = 5V, R L = 350Ω , C L = 15pF, I F = 7.5mA
t PHL
tr , tf
t ELH
Ta = 25˚C, V CC = 5V, R L = 350Ω , C L = 15pF, I F = 7.5mA
RL = 350Ω , C L = 15pF, I F = 7.5mA
RL = 350Ω , C L = 15pF, I F = 7.5mA, V EH = 3.0V, V EL = 0.5V
t EHL RL = 350Ω , C L = 15pF, I F = 7.5mA, V EH = 3.0V, V EL = 0.5V
CMH V CM = 10V, R L = 350Ω , V O ( min. ) = 2V, I F = 0mA
CML VCM = 10V, R L = 350Ω , V O (max. ) = 0.8V, I F = 5mA
MIN.
-
-
-
-
-
-
-
-
-
-
5
-
-
-
-
-
-
-
-
-
Note ) Typical values are all at V CC = 5V, Ta = 25˚C
*1 Measured as 2-pin element. Connect pins 2 and 3, connect pins 5, 6, 7 and 8.
*2 At Iin = 10 mA, VF decreases at the rate of 1.6mV/˚C if the temperature goes up.
*3 DC current transfer ratio is defined as the ratio of output collector current to forward bias input current.
*4, *5 Refer to the Fig. 1.
*6, *7 Refer to the Fig. 2.
*8 CM H represents a common mode voltage ignorable rise time ratio that can hold logic( 1) state in output.
CM L represents a common mode voltage ignorable fall time ratio that can hold logic( 0) state in output.
s Recommmended Operating Conditions
TYP.
2
0.4
- 0.8
- 1.2
7
13
-
1012
0.6
1.6
-
60
700
45
45
20, 30
40
15
500
- 500
MAX. Unit
250
µA
0.6
V
-
mA
- 2.0 mA
15
mA
18
mA
1.0
mA
-
Ω
-
pF
1.75
V
-
V
-
pF
-
%
75
ns
75
ns
-
ns
-
ns
-
ns
-
V/ µ s
-
V/ µ s
Parameter
Low level input current
High level input current
High level enable voltage
Low level enable voltage
Supply voltage
Fanout ( TTL load )
Operating temperature
Symbol
I FL
I FH
V EH
V EL
V CC
N
T opr
MIN.
MAX.
Unit
0
250
µA
7.0
15
mA
2.0
V CC
V
0
0.8
V
4.5
5.5
V
-
8
-
0
70
˚C
1. No necessary external pull-up resistor to hold enable input at high level
2. Connect a ceramic by-pass capacitor ( 0.01 to 0.1 µ F ) between VCC and GND at the position within 1cm from pin.
Circuit Block Diagram
Anode
Cathode
V CC
VE
(Enable)
VO
GND
Truth Table
Input Enable Output
H
H
L
L
H
H
H
L
H
L
L
H
L:Logic (0) H:Logic (1)
Share Link: 