SC1102(2000) Ver la hoja de datos (PDF) - Semtech Corporation

Número de pieza

componentes Descripción

Fabricante

SC1102
(Rev.:2000)

SYNCHRONOUS DC/DC CONTROLLER FOR DISTRIBUTED POWER SUPPLY APPLICATIONS

Semtech Corporation 

SYNCHRONOUS DC/DC CONTROLLER FOR

SC1102

DISTRIBUTED POWER SUPPLY APPLICATIONS

September 5, 2000

THEORY OF OPERATION

Synchronous Buck Converter

Primary VCORE power is provided by a synchronous,

voltage-mode pulse width modulated (PWM) controller.

This section has all the features required to build a

high efficiency synchronous buck converter, including

“Power Good” flag, shut-down, and cycle-by-cycle cur-

rent limit.

The output voltage of the synchronous converter is set

and controlled by the output of the error amplifier. The

external resistive divider reference voltage is derived

from an internal trimmed-bandgap voltage reference

(See Fig. 1). The inverting input of the error amplifier

receives its voltage from the SENSE pin.

The internal oscillator uses an on-chip capacitor and

trimmed precision current sources to set the oscillation

frequency to 200kHz. The triangular output of the os-

cillator sets the reference voltage at the inverting input

of the comparator. The non-inverting input of the com-

parator receives it’s input voltage from the error ampli-

fier. When the oscillator output voltage drops below the

error amplifier output voltage, the comparator output

goes high. This pulls DL low, turning off the low-side

FET, and DH is pulled high, turning on the high-side

FET (once the cross-current control allows it). When

the oscillator voltage rises back above the error ampli-

fier output voltage, the comparator output goes low.

This pulls DH low, turning off the high-side FET, and

DL is pulled high, turning on the low-side FET (once

the cross-current control allows it).

As SENSE increases, the output voltage of the error

amplifier decreases. This causes a reduction in the on-

time of the high-side MOSFET connected to DH,

hence lowering the output voltage.

Under Voltage Lockout

The under voltage lockout circuit of the SC1102 as-

sures that the high-side MOSFET driver outputs re-

main in the off state whenever the supply voltage drops

below set parameters. Lockout occurs if VCC falls below

4.1V. Normal operation resumes once VCC rises above

4.2V.

Over-Voltage Protection

The over-voltage protection pin (OVP) is high only

when the voltage at SENSE is 20% higher than the tar-

get value programmed by the external resistor divider.

The OVP pin is internally connected to a PNP’s

collector.

Power Good

The power good function is to confirm that the regula-

tor outputs are within +/-10% of the programmed

level. PWRGD remains high as long as this condition

is met. PWRGD is connected to an internal open col-

lector NPN transistor.

Soft Start

Initially, SS/SHDN sources 10µA of current to charge

an external capacitor. The outputs of the error ampli-

fiers are clamped to a voltage proportional to the volt-

age on SS/SHDN. This limits the on-time of the high-

side MOSFETs, thus leading to a controlled ramp-up

of the output voltages.

RDS(ON) Current Limiting

The current limit threshold is set by connecting an

external resistor from the VCC supply to OCSET. The

voltage drop across this resistor is due to the 200µA

internal sink sets the voltage at the pin. This voltage

is compared to the voltage at the PHASE node. This

comparison is made only when the high-side drive is

high to avoid false current limit triggering due to un-

contributing measurements from the MOSFET’s off-

voltage. When the voltage at PHASE is less than the

voltage at OCSET, an overcurrent condition occurs

and the soft start cycle is initiated. The synchronous

switcher turns off and SS/SHDN starts to sink 2µA.

When SS/SHDN reaches 0.8V, it then starts to

source 10µA and a new cycle begins.

Hiccup Mode

During power up, the SS/SHDN pin is internally

pulled low until VCC reaches the undervoltage lock-

out level of 4.2V. Once VCC has reached 4.2V, the

SS/SHDN pin is released and begins to source 10µA

of current to the external soft-start capacitor. As the

soft-start voltage rises, the output of the internal error

amplifier is clamped to this voltage. When the error

signal reaches the level of the internal triangular os-

cillator, which swings from 1V to 2V at a fixed fre-

quency of 200 kHz, switching occurs. As the error

signal crosses over the oscillator signal, the duty cy-

cle of the PWM signal continues to increase until the

output comes into regulation. If an over-current con-

dition has not occurred the soft-start voltage will con-

tinue to rise and level off at about 2.2V.

© 2000 SEMTECH CORP.

7

652 MITCHELL ROAD NEWBURY PARK CA 91320

Share Link: