AM26LS32 Ver la hoja de datos (PDF) - Motorola => Freescale
Número de pieza
componentes Descripción
Fabricante
AM26LS32 Datasheet PDF : 4 Pages
| |||
AM26LS32
MAXIMUM RATINGS
Rating
Power Supply Voltage
Input Common Mode Voltage
Input Differential Voltage
Three–State Control Input Voltage
Output Sink Current
Storage Temperature
Operating Junction Temperature
Symbol
Value
Unit
VCC
7.0
Vdc
VICM
± 25
Vdc
VID
± 25
Vdc
VI
7.0
Vdc
IO
50
mA
Tstg
– 65 to + 150
°C
TJ
+ 150
°C
RECOMMENDED OPERATING CONDITIONS
Rating
Symbol
Value
Unit
Power Supply Voltage
Operating Ambient Temperature
Input Common Mode Voltage Range
Input Differential Voltage Range
VCC
4.75 to 5.25
Vdc
TA
0 to + 70
°C
VICR
– 7.0 to + 7.0
Vdc
VIDR
6.0
Vdc
ELECTRICAL CHARACTERISTICS (Unless otherwise noted, minimum and maximum limits apply over recommended temperature
and power supply voltage ranges. Typical values are for TA = 25°C, VCC = 5.0 V and VIC = 0 V. See Note 1.)
Characteristic
Symbol
Min
Typ
Max
Unit
Input Voltage – High Logic State (Three–State Control)
VIH
2.0
–
Input Voltage – Low Logic State (Three–State Control)
VIL
–
–
Differential Input Threshold Voltage (Note 2)
p p (– 7.0 V VIC 7.0 V, VIH = 2.0 V)
q (IO = – 0.4 mA, VOH 2.7 V)
p (IO = 8.0 mA, VOL 0.45 V)
VTH(D)
–
–
–
–
p p Input Bias Current
(VCC = 0 V or 5.25) (Other Inputs at –15 V Vin + 15 V)
Vin = + 15 V
Vin = – 15 V
p p Input Resistance ( –15 V Vin + 15 V)
IIB(D)
–
–
–
–
Rin
6.0 K
–
p p Input Balance and Output Level
(– 7.0 V VIC 7.0 V, VIH = 2.0 V, See Note 3)
(IO = – 0.4 mA, VID = 0.4 V)
(IO = 8.0 mA, VID = – 0.4 V)
VOH
2.7
–
VOL
–
–
Output Third State Leakage Current
(VI(D) = + 3.0 V, VIL = 0.8 V, VO = 0.4 V)
(VI(D) = – 3.0 V, VIL = 0.8 V, VO = 2.4 V)
IOZ
–
–
–
–
–
0.8
0.2
– 0.2
2.3
– 2.8
–
–
0.45
– 20
20
V
V
V
mA
Ohms
V
µA
Output Short Circuit Current
(VI(D) = 3.0 V, VIH = 2.0 V, VO = 0 V, See Note 4)
IOS
– 15
–
– 85
mA
Input Current – Low Logic State (Three–State Control)
(VIL = 0.4 V)
IIL
–
–
– 360
µA
Input Current – High Logic State (Three–State Control)
(VIH = 2.7 V)
(VIH = 5.5 V)
Input Clamp Diode Voltage (Three–State Control)
(IIC = – 18 mA)
IIH
µA
–
–
20
–
–
100
VIK
–
–
– 1.5
V
Power Supply Current (VIL = 0 V) (All Inputs Grounded)
ICC
–
–
70
mA
NOTES: 1. All currents into device pins are shown as positive, out of device pins are negative. All voltages referenced to ground unless otherwise noted.
2. Differential input threshold voltage and guaranteed output levels are done simultaneously for worst case.
3. Refer to EIA–422/3 for exact conditions. Input balance and guaranteed output levels are done simultaneously for worst case.
4. Only one output at a time should be shorted.
2
MOTOROLA ANALOG IC DEVICE DATA
Share Link: 