SSM2404 Ver la hoja de datos (PDF) - Analog Devices
Número de pieza
componentes Descripción
Fabricante
SSM2404 Datasheet PDF : 8 Pages
| |||
SSM2404–SPECIFICATIONS (VS = ؎12 V, TA = +25؇C, unless otherwise noted.
Typical specifications apply at TA = +25؇C.)
Parameter
Symbol
Conditions
Min Typ Max Units
AUDIO PERFORMANCE
Total Harmonic Distortion Plus Noise
Spectral Noise Density
Wideband Noise Density
ANALOG SIGNAL SECTION
Analog Voltage Range
Analog Current Range
ON Resistance
RON Matching
ON Leakage Current
OFF Leakage Current
Charge Injection
ON-State Input Capacitance
OFF-State Input Capacitance
OFF Isolation
Channel-to-Channel Crosstalk
THD+N
en
en p-p
@ 1 kHz, with 80 kHz Filter,
RL = 100 kΩ, VIN = 2 V rms
20 Hz to 20 kHz
20 Hz to 20 kHz
0.0008
0.8
0.6
%
nV/√Hz
µV p-p
VA
IA
RON
RON Match
IS(ON)
IS(OFF)
Q
VINH = 2.4 V, IA = ± 2 mA
VINH = 2.4 V, VA = 0 V
IA = ± 10 mA, VA = ± 10 V dc
IA = ± 10 mA, VA = 0 V
VA = ± 10 V
VA = ± 10 V
± 12
V
± 10
mA
28 45
Ω
1
%
–20 0.1 +20 nA
–20 0.1 +20 nA
35
pC
CON
COFF
ISO(OFF)
CT
VA = 5 V rms
VA = 5 V rms
VA = 50 mV rms, f = 1 kHz, RL = 10 kΩ
VA = 50 mV rms, f = 1 kHz, RL = 10 kΩ
31
pF
17
pF
–100
dB
–94
dB
CONTROL SECTION
Digital Input High
Digital Input Low
Turn-On Time1
Turn-Off Time2
Break-Before-Make Time Delay
Logic Input Current
Logic HI
Logic LO
POWER SUPPLY
Supply Voltage Range
Positive Supply Current
Negative Supply Current
Ground Current
VINH
VINL
tON
tOFF
tON-tOFF
VS
ISY+
ISY–
DGND = 0 V
DGND = 0 V
See Test Circuit
See Test Circuit
VINH = 2.4 V
VINL = 0.8 V
Single Supply
Dual Supply
All Channels On
All Channels On
All Channels On
2.4
VS
V
0
0.8 V
8
50
ms
5
30
ms
3
20
ms
–1000 1.3 +1000 nA
–1000 1.0 +1000 nA
+11
+24 V
± 5.5
± 12 V
0.9 5
mA
–1.5 –0.6
mA
–2.0 –0.3
mA
NOTES
1Turn-on time is measured from the time the logic input reaches the 50% point to the time the output reaches 50% of the final value.
2Turn-off time is measured from the time the logic input reaches the 50% point to the time the output reaches 50% of the initial value.
Specifications subject to change without notice.
ABSOLUTE MAXIMUM RATINGS
Supply Voltage
Single Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +27 V
Dual Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 13.5 V
Analog Input Voltage (VA) . . . . . . . . . . . . . . . . . . . . . . . . . . VS
Logic Input Voltage (VINL/INH) . . . . . . . . . . . . . . . . . . . . . . VS
Maximum Current Through Any Switch . . . . . . . . . . . 20 mA
Operating Temperature Range . . . . . . . . . . . . –40°C to +85°C
Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C
Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . +150°C
Lead Temperature (Soldering, 60 sec) . . . . . . . . . . . . +300°C
Thermal Resistance1
20-Pin Plastic DIP (P): θJA = 74, θJC = 32 . . . . . . . . . °C/W
20-Pin SOIC (S): θJA = 90, θJC = 27 . . . . . . . . . . . . . . °C/W
NOTE
1θJA is specified for worst case mounting conditions, i.e., θJA is specified for device
in socket for P-DIP package.
ORDERING GUIDE
Model
Operating
Temperature
Range
Package
Package
Option*
SSM2404P –40°C to +85°C 20-Pin Plastic DIP N-20
SSM2404S –40°C to +85°C 20-Pin SOIC
R-20
*N = Plastic DIP, R = SOIC.
–2–
REV. B
Share Link: 