MAX362ETE Ver la hoja de datos (PDF) - Maxim Integrated
Número de pieza
componentes Descripción
Fabricante
MAX362ETE Datasheet PDF : 10 Pages
| |||
Precision Quad SPST Analog Switches
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
COMMON DIMENSIONS
PKG.
16L 5x5
20L 5x5
28L 5x5
32L 5x5
40L 5x5
SYMBOL MIN. NOM. MAX. MIN. NOM. MAX. MIN. NOM. MAX. MIN. NOM. MAX. MIN. NOM. MAX.
A
0.70 0.75 0.80 0.70 0.75 0.80 0.70 0.75 0.80 0.70 0.75 0.80 0.70 0.75 0.80
A1
0 0.02 0.05 0 0.02 0.05 0 0.02 0.05 0 0.02 0.05 0 - 0.05
A3
0.20 REF.
0.20 REF.
0.20 REF.
0.20 REF.
0.20 REF.
b
0.25 0.30 0.35 0.25 0.30 0.35 0.20 0.25 0.30 0.20 0.25 0.30 0.15 0.20 0.25
D
4.90 5.00 5.10 4.90 5.00 5.10 4.90 5.00 5.10 4.90 5.00 5.10 4.90 5.00 5.10
E
4.90 5.00 5.10 4.90 5.00 5.10 4.90 5.00 5.10 4.90 5.00 5.10 4.90 5.00 5.10
e
0.80 BSC.
0.65 BSC.
0.50 BSC.
0.50 BSC.
0.40 BSC.
k
0.25 - - 0.25 - - 0.25 - - 0.25 - - 0.25 0.35 0.45
L
0.30 0.40 0.50 0.45 0.55 0.65 0.45 0.55 0.65 0.30 0.40 0.50 0.40 0.50 0.60
L1
- - - - - - - - - - - - 0.30 0.40 0.50
N
16
20
28
32
40
ND
4
5
7
8
10
NE
4
5
7
8
10
JEDEC
WHHB
WHHC
WHHD-1
WHHD-2
-
PKG.
CODES
T1655-1
T1655-2
T2055-2
T2055-3
T2055-4
T2855-1
T2855-2
T2855-3
T2855-4
T2855-5
T2855-6
T2855-7
T3255-2
T3255-3
T3255-4
T4055-1
EXPOSED PAD VARIATIONS
MIN.
3.00
D2
NOM. MAX. MIN.
3.10 3.20 3.00
E2
NOM.
3.10
MAX.
3.20
DOWN
BONDS
ALLOWED
NO
3.00 3.10 3.20 3.00 3.10 3.20 YES
3.00 3.10 3.20 3.00 3.10 3.20 NO
3.00 3.10 3.20 3.00 3.10 3.20 YES
3.00 3.10 3.20 3.00 3.10 3.20 NO
3.15 3.25 3.35 3.15 3.25 3.35 NO
2.60 2.70 2.80 2.60 2.70 2.80 NO
3.15 3.25 3.35 3.15 3.25 3.35 YES
2.60 2.70 2.80 2.60 2.70 2.80 YES
2.60 2.70 2.80 2.60 2.70 2.80 NO
3.15 3.25 3.35 3.15 3.25 3.35
2.60 2.70 2.80 2.60 2.70 2.80
3.00 3.10 3.20 3.00 3.10 3.20
3.00 3.10 3.20 3.00 3.10 3.20
NO
YES
NO
YES
3.00 3.10 3.20 3.00 3.10 3.20 NO
3.20 3.30 3.40 3.20 3.30 3.40 YES
NOTES:
1. DIMENSIONING & TOLERANCING CONFORM TO ASME Y14.5M-1994.
2. ALL DIMENSIONS ARE IN MILLIMETERS. ANGLES ARE IN DEGREES.
3. N IS THE TOTAL NUMBER OF TERMINALS.
4. THE TERMINAL #1 IDENTIFIER AND TERMINAL NUMBERING CONVENTION SHALL CONFORM TO JESD 95-1
SPP-012. DETAILS OF TERMINAL #1 IDENTIFIER ARE OPTIONAL, BUT MUST BE LOCATED WITHIN THE
ZONE INDICATED. THE TERMINAL #1 IDENTIFIER MAY BE EITHER A MOLD OR MARKED FEATURE.
5. DIMENSION b APPLIES TO METALLIZED TERMINAL AND IS MEASURED BETWEEN 0.25 mm AND 0.30 mm
FROM TERMINAL TIP.
6. ND AND NE REFER TO THE NUMBER OF TERMINALS ON EACH D AND E SIDE RESPECTIVELY.
7. DEPOPULATION IS POSSIBLE IN A SYMMETRICAL FASHION.
8. COPLANARITY APPLIES TO THE EXPOSED HEAT SINK SLUG AS WELL AS THE TERMINALS.
9. DRAWING CONFORMS TO JEDEC MO220, EXCEPT EXPOSED PAD DIMENSION FOR T2855-1,
T2855-3 AND T2855-6.
10. WARPAGE SHALL NOT EXCEED 0.10 mm.
PACKAGE OUTLINE
16, 20, 28, 32, 40L, THIN QFN, 5x5x0.8mm
21-0140
E
2
2
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
10 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2004 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.
Share Link: 