OPL530 Ver la hoja de datos (PDF) - Optek Technology
Número de pieza
componentes Descripción
Fabricante
OPL530 Datasheet PDF : 8 Pages
| |||
Photologic Sensor
OPL530, OPL531, OPL535, OPL536, OPL550, OPL551,
OPL560, OPL561, OPL562, OPL563
Electrical Characteristics (TA = 25°C unless otherwise noted)
SYMBOL
PARAMETER
MIN TYP MAX UNITS
TEST CONDITIONS
Operating Supply Voltage
OPL550
VOH
OPL551
OPL560
OPL561
2.4 3.3 -
2.4 3.3 -
VCC -2.1 -
-
VCC -2.1 -
-
V VCC = 4.5 V, IOH = -800 µa,
EE = 3 mW/cm2
V VCC = 4.5 V, IOH = -800 µa,
EE = 0
V IOH = -1 µA, EE = 1 mW/cm2
V IOH = -1 µA, EE = 0
Low Level Output Voltage
OPL530, OPL530-OC, OPL535, OPL535-OC
OPL531, OPL531-OC, OPL536, OPL536-OC
- 0.2 0.4
- 0.2 0.4
V IOL = 16 mA, EE = 0
V IOL = 16 mA, EE = 1 mW/cm2
VOL
OPL550
OPL551
OPL560, OPL560-OC
OPL561, OPL561-OC
- 0.25 0.4
- 0.25 0.4
-
- .4
-
- .4
V VCC = 4.5 V, IOL = 12.8 mA,
EE = 0
V VCC = 4.5 V, IOL = 12.8 mA,
EE = 3 mW/cm2
V IOL = 16 mA, EE = 0
V IOL = 16 mA, EE = 1 mW/cm2
Short Circuit Output Current
OPL550
IOS
OPL551
High Level Output Current(4)
OPL531, OPL531-OC, OPL536, OPL536-OC
OPL535, OPL535-OC, OPL530, OPL530-OC
-20 -55 -100 mA VCC = 5.5 V, Output = GND,
EE = 3 mW/cm2
-20 -55 -100 mA VCC = 5.5 V, Output = GND,
EE = 0
-
0.1 10
µA VOH = 30 V, EE = 0
-
0.1 10
µA VOH = 30 V, EE = 1 mW/cm2
IOH
OPL550-OC
OPL551-OC
OPL560-OC
-
1 100 µA VCC = 4.5 V, VOH = 30 V,
EE = 3 mW/cm2
-
1 100 µA VCC = 4.5 V, VOH = 30 V,
EE = 0
-
- 100
µA VOH = 30 V, EE = 1 mW/cm2
OPL561-OC
-
- 100 µA VOH = 30 V, EE = 0
Notes:
(1) RMA flux is recommended. Duration can be extended to 10 sec. max. when flow soldering. For OPL530, OPL530-OC,
OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536 and OPL536-OC, a maximum of 20 grams force may be applied to leads
while at soldering temperatures.
(2) Derate linearly 2.67 mW/°C above 70° C for OPL530, OPL530-OC, OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536 and
OPL536-OC. Derate linearly 2.5 mW/° C above 25° C for all devices in the OPL550, OPL551, OPL560, OPL561, OPL562 and
OPL563 series.
(3) Irradiance measurements are made with λi = 935 nm.
(4) This applies to OC versions only. For ICC on pull-up versions, add VCC/10 KΩ.
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
Issue A 09/08
Page 6 of 8
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
Share Link: 