FAN7171-F085 Ver la hoja de datos (PDF) - ON Semiconductor
Número de pieza
componentes Descripción
Fabricante
FAN7171-F085 Datasheet PDF : 11 Pages
| |||
FAN7171−F085
7. Input pulses shorter than the minimum recommendation can cause abnormal output. Short input pulses can be turn on pulses (i.e., rising
edge to the adjacent falling edge), turn off pulses (i.e., falling edge to the adjacent rising edge) but also parasitic pulses induced by noise.
Refer to Figure 24 and Figure 25. Value guaranteed by design.
Table 4. ELECTRICAL CHARACTERISTICS
(VBIAS (VDD, VBS) = 15 V, −40°C ≤ TA ≤ 125°C, unless otherwise specified. The VIN and IIN parameters are referenced to GND. The VO
and IO parameters are relative to VS and are applicable to the respective output HO)
Symbol
Parameter
Conditions
Min.
Typ.
Max.
Unit
POWER SUPPLY SECTION
IQDD
IPDD
Quiescent VDD Supply Current
Operating VDD Supply Current
VIN = 0 V or 5 V
fIN = 20 kHz,
No Load
25
70
μA
35
100
μA
BOOTSTRAPPED SUPPLY SECTION
VBSUV+ VBS Supply Under−Voltage Positive-Going
Threshold Voltage
VBS = Sweep
8.2
9.2
10.2
V
VBSUV− VBS Supply Under−Voltage Negative−Going
Threshold Voltage
VBS = Sweep
7.5
8.5
9.5
V
VBSHYS
ILK
IQBS
IPBS
VBS Supply UVLO Hysteresis Voltage
Offset Supply Leakage Current
Quiescent VBS Supply Current
Operating VBS Supply Current
VBS = Sweep
VB = VS = 600 V
VIN = 0 V or 5 V
CLOAD = 1 nF,
fIN = 20 kHz,
RMS Value
0.6
V
50
μA
60
120
μA
0.73
2.80
mA
SHUNT REGULATOR SECTION
VSHUNT VDD and VBS Shunt Regulator Clamping Voltage
ISHUNT = 5 mA
23
25
V
INPUT LOGIC SECTION (IN)
VIH
Logic “1” Input Voltage
VIL
Logic “0” Input Voltage
IIN+
Logic Input High Bias Current
IIN−
Logic Input Low Bias Current
RIN
Input Pull−down Resistance
GATE DRIVER OUTPUT SECTION (HO)
VIN = 5 V
VIN = 0 V
2.5
V
0.8
V
45
125
μA
2
μA
40
110
kΩ
VOH
High Level Output Voltage (VBIAS − VO)
VOL
Low Level Output Voltage
IO+
Output High, Short−Circuit Pulsed Current (Note 8)
No Load
No Load
VHO = 0 V,
VIN = 5 V,
PW ≤ 10 μs
1.5
V
35
mV
3.0
4.0
A
IO−
Output Low, Short−Circuit Pulsed Current (Note 8)
VHO = 15 V,
3.0
4.0
A
VIN = 0 V,
PW ≤ 10 μs
VS
Allowable Negative VS Pin Voltage for IN Signal
Propagation to HO
−9.8
−7.0
V
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
8. These parameters guaranteed by design.
Table 5. DYNAMIC ELECTRICAL CHARACTERISTICS
(VBIAS (VDD, VBS) = 15 V, VS = GND = 0 V, CL =1000 pF, and −40°C ≤ TA ≤ 125°C, unless otherwise specified)
Symbol
Parameter
Conditions
Min.
Typ.
tON
Turn−On Propagation Delay
tOFF
Turn−Off Propagation Delay
VS = 0 V
150
VS = 0 V
150
Max.
Unit
210
ns
210
ns
www.onsemi.com
4
Share Link: 