CY7C65213-28PVXI Ver la hoja de datos (PDF) - Cypress Semiconductor

Número de pieza

componentes Descripción

Fabricante

CY7C65213-28PVXI

USB-UART LP Bridge Controller

Cypress Semiconductor 

CY7C65213

CY7C65213A

Electrical Specifications

Absolute Maximum Ratings

Exceeding maximum ratings [1] may shorten the useful life of the

device.

Storage temperature .................................... –55 °C to +100 °C

Ambient temperature with

power supplied (Industrial) ............................ –40 °C to +85 °C

Supply voltage to ground potential

VCCIO ................................................................................ 6.0 V

VCC ................................................................................... 6.0 V

VCCD ............................................................................... 1.95 V

VGPIO .................................................................. VCCIO + 0.5 V

Static discharge voltage ESD protection levels:

■ 2.2-kV HBM per JESD22-A114

Latch-up current ........................................................... 140 mA

Maximum current per GPIO ............................................ 25 mA

Operating Conditions

TA (ambient temperature under bias)

Industrial ........................................................ –40 °C to +85 °C

VCC supply voltage .......................................... 3.15 V to 5.25 V

VCCIO supply voltage ....................................... 1.71 V to 5.50 V

VCCD supply voltage ........................................ 1.71 V to 1.89 V

Device-Level Specifications

All specifications are valid for –40 °C  TA  85 °C, TJ  100 °C, and 1.71 V to 5.50 V, except where noted.

Table 3. DC Specifications

Parameter

Description

VCC

VCC supply voltage

VCCIO

VCCIO supply voltage

VCCD

Output voltage (for core logic)

Cefc

ICC1

ICC2

External Regulator voltage bypass

Operating supply current

USB Suspend supply current

Min

Typ

Max Units

Details/Conditions

3.15

3.30

3.45

4.35

5.00

5.25

1.71

1.80

1.89

2.0

3.3

5.5

–

1.80

–

1.00

1.30

1.60

V Set and configure correct voltage

V

range using the configuration utility

for VCC.

V Used to set I/O voltage. Set and

V

configure the correct voltage range

using the configuration utility for

VCCIO.

V Do not use this supply to drive the

external device.

• 1.71 V  VCCIO 1.89 V: Short

VCCD pin with the VCCIO pin

• VCCIO > 2 V – connect a 1-µF

capacitor (Cefc) between the

VCCD pin and ground

µF X5R ceramic or better

–

13

18

mA USB 2.0 FS,

UART at 1-Mbps single channel,

no GPIO switching at

VCC = 5 V, VCCIO = 5 V

–

5

–

µA Does not include current through the

pull-up resistor on USBDP

In USB suspend mode, the D+

voltage can go up to a maximum of

3.8 V.

Table 4. AC Specifications

Parameter

Description

ZOUT

USB driver output impedance

Twakeup

Wakeup from USB Suspend mode

Min

Typ

Max Units

Details/Conditions

28

–

44

 As CY7C65213 has internal

termination resistors, external

resistors are not required.

–

25

–

µs

Note

1. Usage above the absolute maximum conditions may cause permanent damage to the device. Exposure to Absolute Maximum conditions for extended periods of

time may affect device reliability. When used below Absolute Maximum conditions but above normal operating conditions, the device may not operate to specification.

Document Number: 001-81011 Rev. *M

Page 9 of 29

Share Link: