ADDC02808PBTV/QMLH Ver la hoja de datos (PDF) - Analog Devices
Número de pieza
componentes Descripción
Fabricante
ADDC02808PBTV/QMLH Datasheet PDF : 20 Pages
| |||
ADDC02808PB
Screening Steps
Pre-Cap Visual
Temp Cycle
Constant Acceleration
Fine Leak
Gross Leak
Burn-In
Final Electrical Test
Screening Levels for ADDC02808PB
Industrial (KV)
100%
N/A
N/A
Guaranteed to Meet
MIL-STD-883, TM1014
Guaranteed to Meet
MIL-STD-883, TM1014
N/A
At +25°C, Per Specification
Table
Ruggedized Industrial (TV)
MIL-STD-883, TM2017
N/A
N/A
Guaranteed to Meet
MIL-STD-883, TM1014
Guaranteed to Meet
MIL-STD-883, TM1014
MIL-STD-883, TM1015,
96 Hrs at +125°C Case
At +25°C, Per Specification
Table
MIL-STD-883B/SMD (TV/QMLH)
Compliant to MIL-PRF-38534
NOMINAL CASE DIMENSIONS IN INCHES AND (mm).
[All tolerances ± 0.005" (±.13 mm) unless otherwise specified]
0.100 (2.54)
8 PLCS
0.149 (3.78) 0.300 (7.62) SQ
0.150 (3.81) DIA TYP
؎ 0.010
4 PLCS
4 PLCS
0.150 (3.81)
0.200 (5.08)
0.200 (5.08)
0.150 (3.81)
0.390 ؎ 0.010
(9.91 ؎ 0.25)
TOP VIEW
0.800 ؎ 0.010
(20.32 ؎ 0.25)
1.145 (29.08)
2 PLCS
4 PLCS
2.745 ؎ 0.010
(69.72 ؎ 0.25)
1.500 ؎ 0.010
(38.10 ؎ 0.25)
1.800
(45.72)
TYP
0.200 (5.08) 5 PLCS
0.250 (6.35)
2 PLCS
2.100 ؎ 0.010
(53.34 ؎ 0.25)
0.040 ؎ 0.003
(1.02 ؎ 0.08)
0.090 ؎ 0.010
(2.29 ؎ 0.25)
NOTES
1. The final product weight is 85 grams maximum.
2. The package base material is made of molybdenum and is
nominally 40 mils (1.02 mm) thick. The “runout” is less
than 2 mils per inch (0.02 mm per cm).
3. The high current pins (10–17) are 40 mil (1.02 mm) diameter;
are 99.8% copper; and are plated with gold over nickel.
4. The signal carrying pins (1–9) are 18 mil (0.46 mm) diam-
eter; are Kovar; and are plated with gold over nickel.
5. All pins are a minimum length of 0.740 inches (18.80 mm)
when the product is shipped. The pins are typically bent up
or down and cut shorter for proper connection into the user’s
system.
6. All pin-to-sidewall spacings are guaranteed for a minimum of
500 V dc breakdown at standard air pressure.
7. The case outline was originally designed using the inch-pound
units of measurement. In the event of conflict between the
metric and inch-pound units, the inch-pound shall take
precedence.
–20–
REV. A
Share Link: 