HIP4020(1997) Ver la hoja de datos (PDF) - Intersil
Número de pieza
componentes Descripción
Fabricante
HIP4020 Datasheet PDF : 8 Pages
| |||
HIP4020
Absolute Maximum Ratings
Supply Voltage; VDD to VSS or VSSA or VSSB . . . . . . . . . . . . . . +15V
Neg. Output Supply Voltage, (VSSA, VSSB). . . . . . . . . . . . . (Note 1)
DC Logic Input Voltage (Each Input) . . . (VSS -0.5V) to (VDD +0.5V)
DC Logic Input Current (Each Input) . . . . . . . . . . . . . . . . . . . . .±15mA
ILF Fault Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .±15mA
Output Load Current, (Self Limiting, See Elec. Spec.). . . . . ±IO(LIMIT)
Thermal Information
Thermal Resistance (Typical, Note 1)
θJA
Plastic SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . 105oC/W
Maximum Storage Temperature Range . . . . . . . . . . -65oC to 150oC
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC
(Lead Tips Only)
Operating Conditions TA = 25oC
Typical Operating Supply Voltage Range, VDD. . . . . . . . +3 to +12V
Low Voltage Logic Retention, Min. VDD . . . . . . . . . . . . . . . . . . . +2V
Idle Supply Current; No Load, VDD = +5V . . . . . . . . . . . . . . . 0.8mA
Typical P+N Channel rDS(ON), VDD = +5V, 0.5A Load . . . . . . . . . 2Ω
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1. θJA is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications TA = 25oC, VDD = +5V, VSSA = VSSB = VSS = 0V, Unless Otherwise Specified
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
TYP
MAX UNITS
Input Leakage Current
ILEAK VDD = +15V
-
-
25
nA
Low Level Input Voltage
VIL
VSS
-
0.8
V
High Level Input Voltage
VIH
2
-
VDD
V
ILF Output Low, Sink Current
IOH
VOUT = 0.4V, VDD = +12V
15
-
-
mA
ILF Output High, Source Current
IOL
VOUT = 11.6V, VDD = +12V
-
-
-15
mA
Input Capacitance
CIN
-
2
-
pF
P-Channel rDS(ON), Low Supply Voltage
rDS(ON) VDD = +3V, ISOURCE = 250mA
-
1.6
2.1
Ω
N-Channel rDS(ON), Low Supply Voltage
rDS(ON) VDD = +3V, ISINK = 250mA
-
1
1.5
Ω
P-Channel rDS(ON), High Supply Voltage
rDS(ON) VDD = +12V, ISOURCE = 400mA
-
0.6
1.2
Ω
N-Channel rDS(ON), High Supply Voltage
rDS(ON) VDD = +12V, ISINK = 400mA
-
0.5
1.1
Ω
OUTA, OUTB Source Current Limiting
IO(LIMIT) VDD = +6V, VSS = 0V, VSSA = VSSB = -6V 480
625 1500
mA
OUTA, OUTB Sink Current Limiting
-IO(LIMIT) VDD = +6V, VSS = 0V, VSSA = VSSB = -6V 480
800 1500
mA
Idle Supply Current; No Load
IDD
-
0.8
1.5
mA
OUTA, OUTB Voltage High
VOH
ISOURCE = 450mA
4.2
4.5
-
V
OUTA, OUTB Voltage Low
VOL
ISINK = 450mA
-
0.4
0.6
V
OUTA, OUTB Voltage High
VOH
VDD = +3V, ISOURCE = 250mA
2.415 2.6
-
V
OUTA, OUTB Voltage Low
VOL
VDD = +3V, ISINK = 250mA
-
0.25 0.375
V
OUTA, OUTB Source Current Limiting
IO(LIMIT) VDD = +12V
480
625 1500
mA
OUTA, OUTB Sink Current Limiting
-IO(LIMIT) VDD = +12V
480
800 1500
mA
OUTA, OUTB Source Current Limiting
IO(LIMIT) VDD = +3V
480
625 1500
mA
OUTA, OUTB Sink Current Limiting
Thermal Shutdown
-IO(LIMIT)
TSD
VDD = +3V
480
800 1500
mA
-
145
-
oC
2
Share Link: 