RH56D-PCI Ver la hoja de datos (PDF) - Unspecified

Número de pieza

componentes Descripción

Fabricante

RH56D-PCI

Host-Controlled V.90/K56flex™ Modem device Family for Desktop Applications

Unspecified 

RH56D-PCI Modem Designer’s Guide

and status signals routed through it. A DAA section is also governed by local government regulations covering subjects

such as component spacing, high voltage suppression, and current limiting.

3. Once sections have been roughly defined, place the components starting with the connectors and jacks.

a) Allow sufficient clearance around connectors and jacks for mating connectors and plugs.

b) Allow sufficient clearance around components for power and ground traces.

c) Allow sufficient clearance around sockets to allow the use of component extractors.

4. First, place the mixed analog/digital components (e.g., modem device, A/D converter, and D/A converter).

a) Orient the components so pins carrying digital signals extend onto the digital section and pins carrying analog

signals extend onto the analog section as much as possible.

b) Position the components to straddle the border between analog and digital sections.

5. Place all analog components.

a) Place the analog circuitry, including the DAA, on the same area of the PCB.

b) Place the analog components close to and on the side of board containing the TXA1, TXA2, RXA, VC, and VREF

signals.

c) Avoid placing noisy components and traces near TXA1, TXA2, RXA, VC, and VREF lines.

6. Place active digital components/circuits and decoupling capacitors.

a) Place digital components close together in order to minimize signal trace length.

b) Place 0.1 µF decoupling (bypass) capacitors close to the pins (usually power and ground) of the IC they are

decoupling. Make the smallest loop area possible between the capacitor and power/ground pins to reduce EMI.

c) Place host bus interface components close to the edge connector in accordance with the applicable bus interface

standard, e.g., the PCI Bus Specification.

d) Place crystal circuits as close as possible to the devices they drive.

7. Provide a “connector” component, usually a zero ohm resistor or a ferrite bead at one or more points on the PCB to

connect one section’s ground to another.

4.1.3 Signal Routing

1. Route the modem signals to provide maximum isolation between noise sources and noise sensitive inputs. When layout

requirements necessitate routing these signals together, they should be separated by neutral signals.

2. Keep digital signals within the digital section and analog signals within the analog section. (Previous placement of

isolation traces should prevent these traces from straying outside their respective sections.) Route the digital traces

perpendicular to the analog traces to minimize signal cross coupling.

3. Provide isolation traces (usually ground traces) to ensure that analog signals are confined to the analog section and

digital traces remain out of the analog section. A trace may have to be narrowed to route it though a mixed analog/digital

IC, but try to keep the trace continuous.

a) Route an analog isolation ground trace, at least 50 mil to 100 mil wide, around the border of the analog section; put

on both sides of the PCB.

b) Route a digital isolation ground trace, at least 50 mil to 100 mil wide, and 200 mil wide on one side of the PCB edge,

around the border of the digital section.

4. Keep host interface signals (e.g., AEN, IOR#, IOW#, HRESET) traces at least 10 mil thick (preferably 12 - 15 mil).

5. Keep analog signal (e.g., the TXA1, TXA2, RXA, TELIN, TELOUT, MIC_V, and SPKOUT) traces at least 10 mil thick

(preferably 12 - 15 mil).

6. Keep all other signal traces as wide as possible, at least 5 mil (preferably 10 mil).

7. Route the signals between components by the shortest possible path (the components should have been previously

placed to allow this).

8. Route the traces between bypass capacitors to IC pins, at least 25 mil wide; avoid vias if possible.

9. Gather signals that pass between sections (typically low speed control and status signals) together and route them

between sections through a path in the isolation ground traces at one (preferred) or two points only. If the path is made

4-2

Conexant

1213

Conexant Proprietary Information

Share Link: