MX29L1611 Ver la hoja de datos (PDF) - Macronix International
Número de pieza
componentes Descripción
Fabricante
MX29L1611 Datasheet PDF : 34 Pages
| |||
MX29L1611G / MX29L1611*
"set-up" command-80H. Two more "unlock" write cycles
are then followed by the chip erase command-10H.
Chip erase does not require the user to program the
device prior to erase.
The automatic erase begins on the rising edge of the last
CE pulse in the command sequence and terminates
when the status on Q7 is "1" at which time the device
stays at read status register mode. The device remains
enabled for read status register mode until the CIR
contents are altered by a valid command sequence.(Refer
to table 3,6 and Figure 2,6,8)
Table 5. MX29L1611G Sector Address Table
(Byte-Wide Mode)
A19 A18 A17 A16 A15 Address Range
[A19, -1]
SA0 0 0 0 0 0 000000H--00FFFFH
SA1 0 0 0 0 1 010000H--01FFFFH
SA2 0 0 0 1 0 020000H--02FFFFH
SA3 0 0 0 1 1 030000H--03FFFFH
SA4 0 0 1 0 0 040000H--04FFFFH
... ... ... ... ... ................................
SA31 1 1 1 1 1 1F0000H--1FFFFFH
SECTOR ERASE
Sector erase is a six-bus cycle operation. There are two
"unlock" write cycles. These are followed by writing the
set-up command-80H. Two more "unlock" write cycles
are then followed by the sector erase command-30H.
The sector address is latched on the falling edge of CE,
while the command (data) is latched on the rising edge of
CE.
Sector erase does not require the user to program the
device prior to erase. The system is not required to
provide any controls or timings during these operations.
The automatic sector erase begins on the rising edge of
the last CE pulse in the command sequence and
terminates when the status on Q7 is "1" at which time the
device stays at read status register mode. The device
remains enabled for read status register mode until the
CIR contents are altered by a valid command
sequence.(Refer to table 3,6 and Figure 3,4,6,8)
READ STATUS REGISTER
The MXIC's 16 Mbit flash family contains a status
register which may be read to determine when a program
or erase operation is complete, and whether that operation
completed successfully. The status register may be
read at any time by writing the Read Status command to
the CIR. After writing this command, all subsequent read
operations output data from the status register until
another valid command sequence is written to the CIR.
A Read Array command must be written to the CIR to
return to the Read Array mode.
The status register bits are output on Q3 - Q7(table 6)
whether the device is in the byte-wide (x8) or word-wide
(x16) mode for the MX29L1611G. In the word-wide mode
the upper byte, Q(8:15) is set to 00H during a Read Status
command. In the byte-wide mode, Q(8:14) are tri-stated
and Q15/A-1 retains the low order address function.
It should be noted that the contents of the status register
are latched on the falling edge of OE or CE whichever
occurs last in the read cycle. This prevents possible bus
errors which might occur if the contents of the status
register change while reading the status register. CE or
OE must be toggled with each subsequent status read,
or the completion of a program or erase operation will not
be evident.
The Status Register is the interface between the
microprocessor and the Write State Machine (WSM).
When the WSM is active, this register will indicate the
status of the WSM, and will also hold the bits indicating
whether or not the WSM was successful in performing the
desired operation. The WSM sets status bits four
through seven and clears bits six and seven, but cannot
clear status bits four and five. If Erase fail or Program fail
status bit is detected, the Status Register is not cleared
until the Clear Status Register command is written. The
MX29L1611G automatically outputs Status Register data
when read after Chip Erase, Sector Erase, Page Program
or Read Status Command write cycle. The default state
of the Status Register after powerup and return from deep
power-down mode is (Q7, Q6, Q5, Q4) = 1000B. Q3 = 0
or 1 depends on sector-protect status, can not be
changed by Clear Status Register Command or Write
State Machine.
P/N:PM0604
REV. 0.8, JAN. 24, 2002
10
Share Link: 