M5M5V32R16J-15 Ver la hoja de datos (PDF) - MITSUBISHI ELECTRIC
Número de pieza
componentes Descripción
Fabricante
M5M5V32R16J-15 Datasheet PDF : 8 Pages
| |||
MITSUBISHI LSIs
M5M5V32R16J,TP-10,-12,-15
524288-BIT (32768-WORD BY 16-BIT) CMOS STATIC RAM
ABSOLUTE MAXIMUM RATINGS
Symbol
Parameter
Conditions
Ratings
Unit
Vcc
Supply voltage
-2.0* ~ 4.6
V
VI
Input voltage
With respect to GND -2.0* ~ Vcc+0.5 V
VO
Output voltage
-2.0* ~ Vcc
V
Pd
Power dissipation
Ta=25 C
1000
mW
Topr
Operating temperature
0 ~ 70
C
Tstg(bias) Storage temperature(bias)
-10 ~ 85
C
Tstg
Storage temperature
-65 ~ 150
C
* Pulse width <= 20ns, In case of DC: - 0.5V
DC ELECTRICAL CHARACTERISTICS (Ta=0 ~ 70 C, Vcc=3.3V +-105%%, unless otherwise noted)
Symbol
Parameter
Condition
VIH
VIL
VOH
VOL
II
IOZ
High-level input voltage
Low-level input voltage
High-level output voltage
Low-level output voltage
Input current
Output current in off-state
IOH = - 4mA
IOL= 8mA
V I = 0 ~ Vcc
VI (/S)= VIH
VO= 0 ~ Vcc
Active supply current
I CC1 (TTL level)
VI (/S)= VIL
other inputs VIH or VIL
Output-open(duty 100%)
AC(10ns cycle)
AC(12ns cycle)
AC(15ns cycle)
DC
AC(10ns cycle)
I CC2
Stand-by supply current
(TTL level)
VI (/S)= VIH
AC(12ns cycle)
AC(15ns cycle)
DC
I CC3
Stand-by current
(MOS level)
VI (/S)= Vcc=> 0.2V
other inputs VI <= 0.2V
or VI => Vcc - 0.2V
* Pulse width <= 20ns, in case of AC : - 3.0V
CAPACITANCE (Ta=0 ~ 70 C, Vcc=3.3V+-105%% , unless otherwise noted)
Symbol
Parameter
Test Condition
C I Input capacitance
VI =GND,Vi =25mVrms,f=1MHz
CO Output capacitance
Vo =GND,Vo =25mVrms,f=1MHz
Note 1: Direction for current flowing into an IC is positive (no mark).
2: Typical value is Vcc=3.3V,Ta=25 C
3: CI,CO are periodically sampled and are not 100% tested.
Min
2.0
-0.3*
2.4
Limits
Typ Max
Unit
Vcc+0.3 V
0.8 V
V
0.4 V
2 µA
10 µA
150
130 mA
110
90 100
60
55
50 mA
40
0.1 1 mA
Min
Limit
Typ Max
Unit
6 pF
8 pF
AC ELECTRICAL CHARACTERISTICS (Ta=0 ~ 70 C, Vcc=3.3V +-105%%, unless otherwise noted)
(1) MEASUREMENT CONDITION
Input pulse levels
VIH =3.0V, V IL =0.0V
( ) Including
scope and JIG
Input rise and fall time
3ns
Input timing reference levels
V IH =1.5V, VIL =1.5V
DQ
DQ
Vcc
480Ω
Output timing reference levels
Output loads
V OH =1.5V, V OL =1.5V
Fig1,Fig2
50Ω
VL=1.5V
255Ω 5pF
( ) Including
scope and JIG
Fig.1 Output load
Fig.2 Output load for ten , tdis
MITSUBISHI
ELECTRIC
3
Share Link: 