ADM1021A Ver la hoja de datos (PDF) - ON Semiconductor

Número de pieza

componentes Descripción

Fabricante

ADM1021A

Low Cost Microprocessor System Temperature Monitor Microcomputer

ON Semiconductor 

ADM1021A

Where copper/solder joints are used, ensure they

are in both the D+ and D− paths and at the same

temperature.

Thermocouple effects should not be a major

problem as 1°C corresponds to about 240 mV, and

thermocouple voltages are about 3 mV/°C of

temperature difference. Unless there are two

thermocouples with a big temperature differential

between them, thermocouple voltages should be

much less than 240 mV.

5. Place a 0.1 mF bypass capacitor close to the VDD

pin, and 2200 pF input filter capacitors across D+,

D− close to the ADM1021A.

6. If the distance to the remote sensor is more than

eight inches, the use of twisted pair cable is

recommended. This works up to about 6 to 12 feet.

7. For very long distances (up to 100 feet), use

shielded twisted pair, such as Belden #8451

microphone cable. Connect the twisted pair to D+

and D− and the shield to GND close to the

ADM1021A. Leave the remote end of the shield

unconnected to avoid ground loops.

GND

D+

D–

GND

10MIL

10MIL

10MIL

10MIL

10MIL

10MIL

10MIL

Figure 18. Arrangement of Signal Tracks

Because the measurement technique uses switched

current sources, excessive cable and/or filter capacitance

can affect the measurement. When using long cables, the

filter capacitor can be reduced or removed.

Cable resistance can also introduce errors. A series

resistance of 1 W introduces about 1°C error.

Application Circuits

Figure 19 shows a typical application circuit for the

ADM1021A, using a discrete sensor transistor connected

via a shielded, twisted pair cable. The pullups on SCLK,

SDATA, and ALERT are required only if they are not

already provided elsewhere in the system.

The SCLK and SDATA pins of the ADM1021A can be

interfaced directly to the SMBus of an I/O chip. Figure 20

shows how the ADM1021A might be integrated into a

system using this type of I/O controller.

C1*

2N3904 SHIELD

* C1 IS OPTIONAL

ADM1021A

VDD

STBY

D+

SCLK

SDATA

D–

ALERT

ADD0

ADD1

GND

0.1µ F

3.3 V

ALL 10k

IN

I/O

OUT

TO CONTROL

CHIP

SET TO REQUIRED

ADDRESS

Figure 19. Typical Application Circuit

PROCESSOR

SYSTEM BUS

D–

D+

ADM1021A

ALERT SDATA SCLK

DISPLAY

GMCH

SYSTEM

MEMORY

DISPLAY

CACHE

PCI SLOTS

HARD

CD−ROM DISK

2 IDE PORTS

USB USB

2 USB PORTS

ICH

I/O CONTROLLER

HUB

PCI BUS

SUPER

I/O

FWH

(FIRMWARE HUB)

SMBus

Figure 20. Typical System Using ADM1021A

ORDERING INFORMATION

Device Number

Temperature Range

Package Type

Package Option

Shipping†

ADM1021AARQZ

0°C to +100°C

16−Lead QSOP

RQ−16

98 Tube

ADM1021AARQZ−R

0°C to +100°C

16−Lead QSOP

RQ−16

2500 Tape & Reel

ADM1021AARQZ−R7

0°C to +100°C

16−Lead QSOP

RQ−16

1000 Tape & Reel

†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging

Specifications Brochure, BRD8011/D.

*The “Z’’ suffix indicates Pb−Free part.

http://onsemi.com

14

Share Link: