PCA9513A Ver la hoja de datos (PDF) - Philips Electronics
Número de pieza
componentes Descripción
Fabricante
PCA9513A Datasheet PDF : 25 Pages
| |||
Philips Semiconductors
PCA9513A; PCA9514A
Hot swappable I2C-bus and SMBus bus buffer
HIGH for the bus idle time or when all pins are HIGH and a STOP condition is seen on the
SDAIN and SCLIN pins, SDAIN is connected to SDAOUT and SCLIN is connected to
SCLOUT.
A 92 µA pull-up current source on SDAIN and SCLIN of the PCA9513A is activated during
the initialization state and remains active until the power is removed or the ENABLE pin is
taken LOW. When the 92 µA pull-up is active it will become high-impedance any time the
pin voltage is greater than VCC, otherwise it provides current to pull the pin up to VCC.
8.2 Connect circuitry
Once the connection circuitry is activated, the behavior of SDAIN and SDAOUT as well as
SCLIN and SCLOUT become identical with each acting as a bidirectional buffer that
isolates the input capacitance from the output bus capacitance while communicating the
logic levels. A LOW forced on either SDAIN or SDAOUT will cause the other pin to be
driven to a LOW by the part. The same is also true for the SCLn pins. Noise between
0.7VCC and VCC is generally ignored because a falling edge is only recognized when it
falls below 0.7VCC with a slew rate of at least 1.25 V/µs. When a falling edge is seen on
one pin, the other pin in the pair turns on a pull-down driver that is referenced to a small
voltage above the falling pin. The driver will pull the pin down at a slew rate determined by
the driver and the load initially, because it does not start until the first falling pin is below
0.7VCC. The first falling pin may have a fast or slow slew rate, if it is faster than the
pull-down slew rate then the initial pull-down rate will continue. If the first falling pin has a
slow slew rate then the second pin will be pulled down at its initial slew rate only until it is
just above the first pin voltage then they will both continue down at the slew rate of the
first.
Once both sides are LOW they will remain LOW until all the external drivers have stopped
driving LOWs. If both sides are being driven LOW to the same value for instance, 10 mV
by external drivers, which is the case for clock stretching and is typically the case for
acknowledge, and one side external driver stops driving that pin will rise until the internal
driver pulls it down to the offset voltage. When the last external driver stops driving a
LOW, that pin will rise up and settle out just above the other pin as both rise together with
a slew rate determined by the internal slew rate control and the RC time constant. As long
as the slew rate is at least 1.25 V/µs, when the pin voltage exceeds 0.8 V for the
PCA9513A and PCA9514A, the rise time accelerators’ circuits are turned on and the
pull-down driver is turned off.
8.3 Maximum number of devices in series
Each buffer adds about 0.1 V dynamic level offset at 25 °C with the offset larger at higher
temperatures. Maximum offset voltage (Voffset) is 0.150 V with a 10 kΩ pull-up resistor.
The LOW level at the signal origination end (master) is dependent upon the load and the
only specification point is the I2C-bus specification of 3 mA will produce VOL < 0.4 V,
although if lightly loaded the VOL may be ∼0.1 V. Assuming VOL = 0.1 V and Voffset = 0.1 V,
the level after four buffers would be 0.5 V, which is only about 0.3 V below the threshold of
the rising edge accelerator (about 0.8 V). With great care a system with four buffers may
work, but as the VOL moves up from 0.1 V, noise or bounces on the line will result in firing
the rising edge accelerator thus introducing false clock edges. Generally it is
recommended to limit the number of buffers in series to two, and to keep the load light to
minimize the offset.
PCA9513A_PCA9514A_1
Product data sheet
Rev. 01 — 11 October 2005
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
6 of 25
Share Link: 