MC100LVEL39(2016) Ver la hoja de datos (PDF) - ON Semiconductor
Número de pieza
componentes Descripción
Fabricante
MC100LVEL39 Datasheet PDF : 6 Pages
| |||
MC100LVEL39
Table 3. MAXIMUM RATINGS
Symbol
Parameter
Condition 1
Condition 2
Rating
Unit
VCC PECL Mode Power Supply
VEE NECL Mode Power Supply
VI
PECL Mode Input Voltage
NECL Mode Input Voltage
Iout
Output Current
VEE = 0 V
VCC = 0 V
VEE = 0 V
VCC = 0 V
Continuous
Surge
VI v VCC
VI w VEE
8 to 0
V
−8 to 0
V
6 to 0
V
−6 to 0
50
mA
100
IBB
VBB Sink/Source
TA
Operating Temperature Range
Tstg Storage Temperature Range
qJA Thermal Resistance (Junction-to-Ambient) 0 lfpm
500 lfpm
SOIC−20 WB
± 0.5
−40 to +85
−65 to +150
90
60
mA
°C
°C
°C/W
qJC Thermal Resistance (Junction-to-Case)
Tsol Wave Solder (Pb-Free)
Standard Board
SOIC−20 WB
< 2 to 3 sec @ 260°C
30 to 35
265
°C/W
°C
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
Table 4. LVPECL DC CHARACTERISTICS (VCC = 3.3 V; VEE = 0.0 V (Note 1))
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
VOH
VOL
VIH
VIL
VBB
VIHCMR
Power Supply Current
Output HIGH Voltage (Note 2)
Output LOW Voltage (Note 2)
Input HIGH Voltage (Single-Ended)
Input LOW Voltage (Single-Ended)
Output Voltage Reference
Input HIGH Voltage Common Mode
Range (Differential) (Note 3)
VPP < 500 mV
VPP ≥ 500 mV
50
59
50
59
54
61
mA
2215 2295 2420 2275 2345 2420 2275 2345 2420 mV
1470 1605 1745 1490 1595 1680 1490 1595 1680 mV
2135
2420 2135
2420 2135
2420 mV
1490
1825 1490
1825 1490
1825 mV
1.92
2.04 1.92
2.04 1.92
2.04 V
V
1.3
2.9 1.2
2.9 1.2
2.9
1.5
2.9 1.4
2.9 1.4
2.9
IIH
Input HIGH Current
IIL
Input LOW Current
150
150
150 mA
0.5
0.5
0.5
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with VCC. VEE can vary ±0.3 V.
2. Outputs are terminated through a 50 W resistor to VCC − 2.0 V.
3. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal.
Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin and 1.0 V.
www.onsemi.com
3
Share Link: 