MACH211SP-10 Ver la hoja de datos (PDF) - Unspecified

Número de pieza

componentes Descripción

Fabricante

MACH211SP-10

High-Performance EE CMOS In-System Programmable Logic

Unspecified 

ABSOLUTE MAXIMUM RATINGS

Storage Temperature . . . . . . . . . . . . . –65°C to +150°C

Ambient Temperature

with Power Applied . . . . . . . . . . . . . –55°C to +125°C

Device Junction Temperature . . . . . . . . . . . . . +150°C

Supply Voltage with

Respect to Ground . . . . . . . . . . . . . . –0.5 V to +7.0 V

DC Input Voltage . . . . . . . . . . . .–0.5 V to VCC + 0.5 V

DC Output or

I/O Pin Voltage . . . . . . . . . . . . . –0.5 V to VCC + 0.5 V

Static Discharge Voltage . . . . . . . . . . . . . . . . . 2001 V

Latchup Current (TA = –40°C to +85°C) . . . . . . 200 mA

Stresses above those listed under Absolute Maximum Ratings

may cause permanent device failure. Functionality at or above

these limits is not implied. Exposure to Absolute Maximum

Ratings for extended periods may affect device reliability.

VANTIS

OPERATING RANGES

Industrial (I) Devices

Temperature (TA)

Operating in Free Air . . . . . . . . . . . . . . –40°C to +85°C

Supply Voltage (VCC)

with Respect to Ground . . . . . . . . . . . +4.5 V to +5.5 V

Operating ranges define those limits between which the

functionality of the device is guaranteed.

DC CHARACTERISTICS over INDUSTRIAL operating ranges

Parameter

Symbol

Parameter Description

Test Conditions

Min Typ Max Unit

VOH Output HIGH Voltage

VOL

Output LOW Voltage

VIH

Input HIGH Voltage

IOH = –3.2 mA, VCC = Min, VIN = VIH or VIL 2.4

IOL = 16 mA, VCC = Min, VIN = VIH or VIL

Guaranteed Input Logical HIGH

Voltage for all Inputs (Note 1)

2.0

3.3

V

0.5

V

V

VIL

Input LOW Voltage

Guaranteed Input Logical LOW

Voltage for all Inputs (Note 1)

0.8

V

IIH

IIL

IOZH

IOZL

ISC

ICC

Input HIGH Leakage Current

VIN = 5.25 V, VCC = Max (Note 2)

Input LOW Leakage Current

VIN = 0 V, VCC = Max (Note 2)

Off-State Output Leakage Current VOUT = 5.25 V, VCC = Max

HIGH

VIN = VIH or VIL (Note 2)

Off-State Output Leakage Current VOUT = 0 V, VCC = Max

LOW

VIN = VIH or VIL (Note 2)

Output Short-Circuit Current

VOUT = 0.5 V, VCC = Max (Note 3)

–30

Supply Current (Static)

VCC = 5 V, TA = 25°C, f = 0 MHz (Note 4)

Supply Current (Active)

VCC = 5 V, TA = 25°C, f = 1 MHz (Note 4)

10

µA

–10

µA

10

µA

–10

µA

–160 mA

40

mA

45

mA

Notes:

1. These are absolute values with respect to device ground and all overshoots due to system and/or tester noise are included.

2. I/O pin leakage is the worst case of IIL and IOZL (or IIH and IOZH).

3. Not more than one output should be shorted at a time. Duration of the short-circuit should not exceed one second.

VOUT = 0.5 V has been chosen to avoid test problems caused by tester ground degradation.

4. This parameter is measured in low-power mode with a 16-bit up/down counter pattern. This pattern is programmed in each PAL

block and is capable of being loaded, enabled and reset.

MACH211SP-10/12/14/18 (Ind)

15

Share Link: