M35500 Ver la hoja de datos (PDF) - MITSUBISHI ELECTRIC
Número de pieza
componentes Descripción
Fabricante
M35500 Datasheet PDF : 16 Pages
| |||
MITSUBISHI <DIGITAL ASSP>
M35500AFP/BGP
FLD(VFD) CONTROLLER
ABSOLUTE MAXIMUM RATINGS
Symbol
VCC
VEE
VI
VI
VI
VO
Parameter
Power source voltage
Pull-down power source voltage
Input voltage AN0 – AN5
Input voltage CS, SIN, SCLK
Input voltage RESET
Output voltage DIG0 – DIG17
SEG0 – SEG17
VO
Output voltage SOUT
Pd
Power dissipation
Topr
Operating temperature
Tstg
Storage temperature
Conditions
Ratings
Unit
• All voltage are based on VSS.
–0.3 to 7.0
V
• Output transistors are cut off.
VCC–45 to VCC+0.3
V
–0.3 to VCC+0.3
V
–0.3 to VCC+0.3
V
–0.3 to VCC+0.3
V
VCC–45 to VCC+0.3
• All voltage are based on VSS.
• Output transistors are cut off.
• A waveform: 450 µs or more
frequency and 30 µs or less
VCC–50 to VCC+0.3
V
pulse width.
• Connect only capacitor load
(CL = 200pF).
• All voltage are based on VSS.
• Output transistors are cut off.
–0.3 to VCC+0.3
V
Ta = 25 °C
600
mW
–20 to 85
°C
–40 to 125
°C
RECOMMENDED OPERATING CONDITIONS (VCC = 4.0 to 5.5 V, Ta = –20 to 85 °C, unless otherwise noted)
Symbol
VCC
VSS
VEE
VIH
VIH
VIL
VIL
Parameter
Power source voltage
Power source voltage
Pull-down power source voltage
“H” input voltage CS, SIN, SCLK
“H” input voltage RESET
“L” input voltage CS, SIN, SCLK
“L” input voltage RESET
Min.
4.0
VCC–38
0.75VCC
0.8VCC
0
0
Limits
Typ.
5.0
0
Unit
Max.
5.5
V
V
VCC
V
VCC
V
VCC
V
0.25VCC V
0.2VCC
V
RECOMMENDED OPERATING CONDITIONS (VCC = 4.0 to 5.5 V, Ta = –20 to 85 °C, unless otherwise noted)
Symbol
Parameter
Limits
Unit
Min.
Typ.
Max.
ΣIOH(peak)
ΣIOH(avg)
“H” total peak output current DIG0 – DIG17, SEG0 – SEG17
“H” total peak output current DIG0 – DIG17, SEG0 – SEG17
(Note 1)
–240 mA
–120 mA
IOH(peak)
“H” peak output current
DIG0 – DIG17
(Note 2)
–40 mA
IOH(peak)
“H” peak output current
SEG0 – SEG7
(Note 2)
–20 mA
IOL(peak)
“L” peak output current
SOUT
10 mA
IOH(avg)
“H” peak output current
DIG0 – DIG17
(Note 3)
–18 mA
IOH(avg)
“H” peak output current
SEG0 – SEG7
(Note 3)
–7 mA
IOL(avg)
“L” peak output current
SOUT
5.0 mA
f(XIN)
Main clock input oscillation frequency
(Note 4)
4.0
5.2 MHz
f(SCLK)
Serial I/O external clock frequency
250
kHz
Notes 1: The total output current is the sum of all the currents flowing through all the applicable ports. The total average current is an average
value measured over 100 ms. The total peak current is the peak value of all the currents.
2: The peak output current is the peak current flowing in each port.
3: The average output current is an average value measured over 100 ms.
4: When the oscillation frequency has a 50 % duty cycle.
10
Share Link: 