AD607 Ver la hoja de datos (PDF) - Analog Devices

Número de pieza

componentes Descripción

Fabricante

AD607

Low Power Mixer 3 V Receiver IF Subsystem

Analog Devices 

VPOS

AD607

2RT

RT

IFOP

BPF

2RT

AD607

are generated at IOUT and QOUT, respectively. The quadra-

ture accuracy of this VFQO is typically –1.2°C at 10.7 MHz. The

PLL uses a sequential-phase detector that comprises low power

emitter-coupled logic and a charge pump (Figure 20).

DMIP

a. Biasing DMIP from Power Supply (Assumes BPF

AC-Coupled Internally)

AD607

RT

IFOP

BPF

DMIP

VMID

RT

CBYPASS

b. Biasing DMIP from VMID (Assumes BPF

AC-Coupled Internally)

Figure 19. Suggested Methods for Biasing Pin DMIP

at VP/2

For IFs < 3 MHz, the on-chip low-pass filters (2 MHz cutoff)

do not attenuate the IF or feedthrough products. Thus, the

maximum input voltage at DMIP must be limited to ± 75 mV

to allow sufficient headroom at the I and Q outputs for not only

the desired baseband signal, but also the unattenuated higher-

order demodulation products. These products can be removed

by an external low-pass filter. In the case of IS54 applications

using a 455 kHz IF and the AD7013 baseband converter, a simple

one-pole RC filter with its corner above the modulation band-

width is sufficient to attenuate undesired outputs.

Phase-Locked Loop

The demodulators are driven by quadrature signals that are

provided by a variable frequency quadrature oscillator (VFQO),

phase-locked to a reference signal applied to Pin FDIN. When

this signal is at the IF, in-phase and quadrature baseband outputs

F

SEQUENTIAL U

PHASE

R

DETECTOR D

REFERENCE CARRIER

(FDIN AFTER LIMITING)

IU~

40␮A

VF

VARIABLE-

FREQUENCY

QUADRATURE

C OSCILLATOR

ID~

R

40␮A

I-CLOCK

90؇

Q-CLOCK

(ECL OUTPUTS)

Figure 20. Simplified Schematic of the PLL and

Quadrature VCO

The reference signal may be provided from an external source

in the form of a high level clock, typically a low level signal

(± 400 mV) since there is an input amplifier between FDIN and

the loop’s phase detector. For example, the IF output itself can

be used by connecting DMIP to FDIN, which will then provide

automatic carrier recover for synchronous AM detection and

take advantage of any post-IF filtering. Pin FDIN must be

biased at VP/2; Figure 22 shows suggested methods.

The VFQO operates from 400 kHz to 12 MHz and is controlled

by the voltage between VPOS and FLTR. In normal operation,

a series RC network forming the PLL loop filter is connected

from FLTR to ground. The use of an integral sample-hold

system ensures that the frequency-control voltage on Pin FLTR

remains held during power-down, so reacquisition of the carrier

typically occurs in 16.5 µs.

In practice, the probability of a phase mismatch at power-up is

high, so the worst-case linear settling period to full lock needs

to be considered in making filter choices. This is typically 16.5 µs

at an IF of 10.7 MHz for a ±100 mV signal at DMIP and FDIN.

Table II. AD607 Gain and Manual Gain Control Voltage vs. Power Supply Voltage

Power Supply

Voltage

(V)

GREF

(= VMID)

(V)

Scale Factor

(dB/V)

3.0

1.5

50.00

3.5

1.75

42.86

4.0

2.0

37.50

4.5

2.25

33.33

5.0

2.5

30.00

5.5

2.75

27.27

Maximum gain occurs for gain control voltage = 0 V.

Scale Factor

(mV/dB)

20.00

23.33

26.67

30.00

33.33

36.67

Gain Control

Voltage Input Range

(V)

0.400–2.000

0.467–2.333

0.533–2.667

0.600–3.000

0.667–3.333

0.733–3.667

REV. C

–17–

Share Link: