ILC7011 Ver la hoja de datos (PDF) - Fairchild Semiconductor
Número de pieza
componentes Descripción
Fabricante
ILC7011 Datasheet PDF : 11 Pages
| |||
ILC7010/7011
PRODUCT SPECIFICATION
Application Information
Capacitor Selection
In general ceramic capacitors are preferred due to their
superior ESR performance.Those with X5R dielectric
offer the best temperature coefficient.
An input capacitor of 1µF or greater, connected between
Input and Ground, located in close proximity to the device
will improve the transient response and the noise rejection.
An output capacitor of at least 1µF is required to maintain
regulator loop stability. Stable operation will be achieved
with a wide variety of capacitors with ESR ranging from
10mΩ to 10Ω.
An optional capacitor connected between the CN pin and
ground can significantly reduce noise on the output.Values
ranging from 470pF to 10nF can be used, depending upon
the sensitivity to output noise in the application. Care should
be taken to prevent noise from external sources to enter into
the CN pin, which is a very sensitive, high impedance pin.
Leakage currents into this pin will directly affect the regula-
tor accuracy and should be kept as low as possible.
Control Functions
Enable Pin
Applying a voltage of 0.6V or less at the Enable pin will
disable the output, reducing the quiescent output current to
less than 1µA, while a voltage of 2V or greater will enable
the device. If this shutdown function is not needed,the pin
can simply be connected to the VIN pin. Allowing this pin to
float will cause erratic operation.
Thermal Protection
The ILC7010/7011 is designed to supply high peak output
currents for brief periods, however this output load will
cause the device temperature to increase and exceed maxi-
mum ratings due to power dissipation.During output over-
load conditions, when the die temperature exceeds the
shutdown limit temperature of 125 °C, onboard thermal
protection will disable the output until the temperature drops
below this limit, at which point the output is then re-enabled.
During a thermal shutdown situation the user may assert the
power-down function at the Enable pin, reducing power
consumption to the minimum level.
Thermal Characteristics
ILC7010/7011 is designed to supply up to 80mA at the
specified output voltage with an operating die (junction)
temperature of up to 125 °C. While the power dissipation is
calculated from known electrical parameters, the thermal
resistance is a result of the thermal characteristics of the
compact SC70 surface-mount package and the surrounding
PC Board copper to which it is mounted.
The relationship describing the thermal behavior of the pack-
age is:
PD(max) = T----J---(--m---Θ-a---xJ---)A---–----T----A--
where TJ(max) is the maximum junction temperature of the
die, which is 125 °C, and TA is the ambient operating
temperature. ΘJA is dependent on the surrounding PC
board layout and can be empirically obtained. While the
ΘJC (junction-to-case) of the SC70 package is specified at
224 °C /W, the ΘJA of the minimum PWB footprint will be at
least 235 °C /W.
This can be improved upon by providing a heat sink of
surrounding copper ground on the PCB.
Depending on the size of the copper area, the resulting ΘJA
can range from approximately 180 °C /W for one square
inch, to nearly 130 °C /W for 4 square inches.
The addition of backside copper with through-holes, stiffen-
ers, and other enhancements can also aid in reducing this
value. The heat contributed by the dissipation of other
devices located nearby must be included in design consider-
ations.
Once the limiting parameters in the thermal relationship
have been determined, the electrical design should be
verified to ensure that the device remains within specified
operating conditions.
If overload conditions are not considered, it is possible for
the device to enter a thermal cycling loop, in which the
circuit enters a shutdown condition, cools, reenables, and
then again overheats and shuts down repeatedly due to an
unmanaged fault condition.
8
REV. 1.0.5 3/21/02
Share Link: 