AD9230(Rev0) Ver la hoja de datos (PDF) - Analog Devices

Número de pieza

componentes Descripción

Fabricante

AD9230
(Rev.:Rev0)

12-Bit, 170 MSPS/210 MSPS/250 MSPS, 1.8 V Analog-to-Digital Converter

Analog Devices 

Table 9. Serial Port Pins

Mnemonic Function

SCLK

SCLK (Serial Clock) is the serial shift clock in.

SCLK is used to synchronize serial interface

reads and writes.

SDIO

SDIO (Serial Data Input/Output) is a dual-purpose

pin. The typical role for this pin is an input and

output depending on the instruction being sent

and the relative position in the timing frame.

CSB

CSB (Chip Select Bar) is active low controls that

gates the read and write cycles.

RESET

Master Device Reset. When asserted, device

assumes default settings. Active low.

The falling edge of the CSB, in conjunction with the rising edge

of the SCLK, determines the start of the framing. An example of

the serial timing and its definitions can be found in Figure 64

and Table 11.

During an instruction phase, a 16-bit instruction is transmitted.

Data then follows the instruction phase and is determined by

the W0 and W1 bits, which is 1 or more bytes of data. All data is

composed of 8-bit words. The first bit of each individual byte of

serial data indicates whether this is a read or write command.

This allows the serial data input/output (SDIO) pin to change

direction from an input to an output.

Data may be sent in MSB or in LSB first mode. MSB first is

default on power-up and can be changed by changing the

configuration register. For more information about this feature

and others, see Interfacing to High Speed ADCs via SPI at

www.analog.com.

AD9230

HARDWARE INTERFACE

The pins described in Table 9 comprise the physical interface

between the user’s programming device and the serial port of

the AD9230. All serial pins are inputs, which is an open-drain

output and should be tied to an external pull-up or pull-down

resistor (suggested value of 10 kΩ).

This interface is flexible enough to be controlled by either

PROMS or PIC mirocontrollers as well. This provides the user

with an alternate method to program the ADC other than a SPI

controller.

If the user chooses not to use the SPI interface, some pins serve

a dual function and are associated with a specific function when

strapped externally to AVDD or ground during device power

on. The Configuration Without the SPI section describes the

strappable functions supported on the AD9230.

CONFIGURATION WITHOUT THE SPI

In applications that do not interface to the SPI control registers,

the SPI SDIO/DCS and SPI SCLK/DFS pins can alternately

serve as standalone CMOS-compatible control pins. When the

device is powered up, it is assumed that the user intends to use

the pins as static control lines for the duty cycle stabilizer. In

this mode, the SPI CSB chip select should be connected to

ground, which disables the serial port interface.

Table 10. Mode Selection

Mnemonic

External

Voltage

SPI SDIO/DCS AVDD

AGND

SPI SCLK/DFS AVDD

AGND

Configuration

Duty cycle stabilizer enabled

Duty cycle stabilizer disabled

Twos complement enabled

Offset binary enabled

tDS

tHI

tCLK

tH

tS

tDH

tLO

CSB

SCLK DON’T CARE

DON’T CARE

SDIO DON’T CARE

R/W

W1

W0

A12

A11

A10

A9

A8

A7

D5

D4

Figure 64. Serial Port Interface Timing Diagram

D3

D2

D1

D0

DON’T CARE

Rev. 0 | Page 25 of 32

Share Link: