AD7951(2015) Ver la hoja de datos (PDF) - Analog Devices
Número de pieza
componentes Descripción
Fabricante
AD7951 Datasheet PDF : 32 Pages
| |||
AD7951
Data Sheet
MODES OF OPERATION
The AD7951 features three modes of operation: warp, normal,
and impulse. Each of these modes is more suitable to specific
applications. The mode is configured with the input pins, WARP
and IMPULSE, or via the configuration register. See Table 6 for
the pin details and the Hardware Configuration section and
Software Configuration section for programming the mode
selection with either pins or configuration register. Note that
when using the configuration register, the WARP and IMPULSE
inputs are don’t cares and should be tied to either high or low.
Warp Mode
Setting WARP = high and IMPULSE = low allows the fastest
conversion rate up to 1 MSPS. However, in this mode, the full
specified accuracy is guaranteed only when the time between
conversions does not exceed 1 ms. If the time between two
consecutive conversions is longer than 1 ms (after power-up),
the first conversion result should be ignored since in warp mode,
the ADC performs a background calibration during the SAR
conversion process. This calibration can drift if the time between
conversions exceeds 1 ms thus causing the first conversion to
appear offset. This mode makes the AD7951 ideal for applications
where both high accuracy and fast sample rate are required.
Normal Mode
Setting WARP = IMPULSE = low or WARP = IMPULSE = high
allows the fastest mode (800 kSPS) without any limitation on
time between conversions. This mode makes the AD7951 ideal
for asynchronous applications such as data acquisition systems,
where both high accuracy and fast sample rate are required.
Impulse Mode
Setting WARP = low and IMPULSE = high uses the lowest power
dissipation mode and allows power saving between conversions.
The maximum throughput in this mode is 670 kSPS and in this
mode, the ADC powers down circuits after conversion making
the AD7951 ideal for battery-powered applications.
TRANSFER FUNCTIONS
Using the OB/2C digital input or via the configuration register,
the AD7951 offers two output codings: straight binary and twos
complement. See Figure 26 and Table 7 for the ideal transfer
characteristic and digital output codes for the different analog
input ranges, VIN. Note that when using the configuration
register, the OB/2C input is a don’t care and should be tied to
either high or low.
111...111
111...110
111...101
000...010
000...001
000...000
–FSR –FSR + 1 LSB
+FSR – 1 LSB
–FSR + 0.5 LSB
+FSR – 1.5 LSB
ANALOG INPUT
Figure 26. ADC Ideal Transfer Function
Table 7. Output Codes and Ideal Input Voltages
VREF = 5 V
Description
VIN = 5 V
VIN = 10 V
VIN = ±5 V
FSR − 1 LSB
4.999695 V 9.999389 V +4.999389 V
FSR − 2 LSB
4.999390 V 9.998779 V +4.998779 V
Midscale + 1 LSB
2.500305 V 5.000610 V +610.4 μV
Midscale
2.5 V
5.000000 V 0 V
Midscale − 1 LSB
2.499695 V 4.999389 V −610.4 μV
−FSR + 1 LSB
305.2 μV
610.4 μV
−4.999389 V
−FSR
0V
0V
−5 V
1 This is also the code for overrange analog input (VIN+ − VIN− above VREF − VREFGND).
2 This is also the code for overrange analog input (VIN+ − VIN− below VREF − VREFGND).
VIN = ±10 V
+9.998779 V
+9.997558 V
+1.221 mV
0V
−1.221 mV
−9.998779 V
−10 V
Digital Output Code
Straight Binary
Twos Complement
0x3FFF1
0x1FFF1
0x3FFE
0x1FFE
0x2001
0x0001
0x2000
0x0000
0x1FFF
0x3FFF
0x0001
0x2001
0x00002
0x20002
Rev. B | Page 18 of 32
Share Link: 