DMO565RBI Ver la hoja de datos (PDF) - Fairchild Semiconductor
Número de pieza
componentes Descripción
Fabricante
DMO565RBI Datasheet PDF : 20 Pages
| |||
FSDM0565RB
Vds Power
on
Fault
occurs
Fault
removed
VFB
6.0V
Over load protection
2.5V
Vcc
T12= Cfb*(6.0-2.5)/Idelay
12V
T1
T2 t
8V
Figure 7. Over load protection
t
Normal
operation
Fault
situation
Normal
operation
Figure 6. Auto restart operation
3.1 Over Load Protection (OLP) : Overload is defined as
the load current exceeding a pre-set level due to an
unexpected event. In this situation, the protection circuit
should be activated in order to protect the SMPS. However,
even when the SMPS is in the normal operation, the over
load protection circuit can be activated during the load
transition. In order to avoid this undesired operation, the over
load protection circuit is designed to be activated after a
specified time to determine whether it is a transient situation
or an overload situation. Because of the pulse-by-pulse
current limit capability, the maximum peak current through
the Sense FET is limited, and therefore the maximum input
power is restricted with a given input voltage. If the output
consumes beyond this maximum power, the output voltage
(Vo) decreases below the set voltage. This reduces the
current through the opto-coupler LED, which also reduces
the opto-coupler transistor current, thus increasing the
feedback voltage (Vfb). If Vfb exceeds 2.5V, D1 is blocked
and the 3.5uA current source starts to charge CB slowly up to
Vcc. In this condition, Vfb continues increasing until it
reaches 6V, when the switching operation is terminated as
shown in Figure 7. The delay time for shutdown is the time
required to charge CB from 2.5V to 6.0V with 3.5uA. In
general, a 10 ~ 50 ms delay time is typical for most
applications.
3.2 Over voltage Protection (OVP) : If the secondary side
feedback circuit were to malfunction or a solder defect
caused an open in the feedback path, the current through the
opto-coupler transistor becomes almost zero. Then, Vfb
climbs up in a similar manner to the over load situation,
forcing the preset maximum current to be supplied to the
SMPS until the over load protection is activated. Because
more energy than required is provided to the output, the
output voltage may exceed the rated voltage before the over
load protection is activated, resulting in the breakdown of the
devices in the secondary side. In order to prevent this
situation, an over voltage protection (OVP) circuit is
employed. In general, Vcc is proportional to the output
voltage and the FSDM0565RB uses Vcc instead of directly
monitoring the output voltage. If VCC exceeds 19V, an OVP
circuit is activated resulting in the termination of the
switching operation. In order to avoid undesired activation of
OVP during normal operation, Vcc should be designed to be
below 19V.
3.3 Thermal Shutdown (TSD) : The Sense FET and the
control IC are built in one package. This makes it easy for
the control IC to detect the heat generation from the Sense
FET. When the temperature exceeds approximately 150°C,
the thermal shutdown is activated.
4. Soft Start : The FSDM0565RB has an internal soft start
circuit that increases PWM comparator inverting input
voltage together with the Sense FET current slowly after it
starts up. The typical soft start time is 10msec, The pulse
width to the power switching device is progressively
increased to establish the correct working conditions for
transformers, inductors, and capacitors. The voltage on the
output capacitors is progressively increased with the
intention of smoothly establishing the required output
voltage. It also helps to prevent transformer saturation and
reduce the stress on the secondary diode during startup.
12
Share Link: 