Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

P/N + Descripción + Búsqueda de contenido

Consulta
Número de pieza(s) : ST92F150CV1T3
ST-Microelectronics
STMicroelectronics
componentes Descripción : 8/16-BIT SINGLE VOLTAGE FLASH MCU FAMILY WITH RAM, E3 TM(EMULATED EEPROM), CAN 2.0B AND J1850 BLPD

GENERAL DESCRIPTION
INTRODUCTION
The ST92124-Auto/150-Auto/250-Auto microcontroller is developed and manufactured by STMicroelectronics using a proprietary n-well HCMOS process. Its performance derives from the use of a flexible 256-register progRAMming model for ultrafast context switching and real-time event response. The intelligent on-chip peripherals offload the ST9 core from I/O and data management processing tasks allowing critical application tasks to get the maximum use of core resources. The new-generation ST9 MCU devices now also support low power consumption and low VOLTAGE operation for power-efficient and low-cost embedded systems.

■ Memories
    – Internal Memory: SINGLE VOLTAGE FLASH up to 256 Kbytes, RAM up to 8Kbytes, 1K byte E3 TM (EMULATED EEPROM)
    – In-Application ProgRAMming (IAP)
    – 224 general purpose registers (register file) available as RAM, accumulators or index pointers
■ Clock, Reset and Supply Management
    – Register-oriented 8/16 bit CORE WITH RUN, WFI, SLOW, HALT and STOP modes
    – 0-24 MHz Operation (Int. Clock), 4.5-5.5 V range
    – PLL Clock Generator (3-5 MHz crystal)
    – Minimum instruction time: 83 ns (24 MHz int. clock)
■ Up to 80 I/O pins
■ Interrupt Management
    – 4 external fast interrupts + 1 NMI
    – Up to 16 pins progRAMmable as wake-up or additional external interrupt WITH multi-level interrupt handler
■ DMA controller for reduced processor overhead
■ Timers
    – 16-bit Timer WITH 8-bit Prescaler, and Watchdog Timer (activated by software or by hardware)
    – 16-bit Standard Timer that CAN be used to generate a time base independent of PLL Clock Generator
    – Two 16-bit independent Extended Function Timers (EFTs) WITH Prescaler, up to two Input Captures and up to two Output Compares
    – Two 16-bit Multifunction Timers, WITH Prescaler, up to two Input Captures and up to two Output Compares
■ Communication Interfaces
    – Serial Peripheral Interface (SPI) WITH Selectable Master/Slave mode
    – One Multiprotocol Serial Communications Interface WITH asynchronous and synchronous capabilities
    – One asynchronous Serial Communications Interface WITH 13-bit LIN Synch Break generation capability
    – J1850 Byte Level Protocol Decoder (JBLPD)
    – Up to two full I²C multiple Master/Slave Interfaces supporting Access Bus
    – Up to two CAN 2.0B Active interfaces
■ Analog peripheral (low current coupling)
    – 10-bit A/D Converter WITH up to 16 robust input channels
■ Development Tools
    – Free High performance Development environment (IDE) based on Visual Debugger, Assembler, Linker, and C-Compiler; Real Time Operating System (OSEK OS, CMX) and CAN drivers
    – Hardware Emulator and FLASH ProgRAMming Board for development and ISP FLASHer for production

Número de pieza(s) : LC62F0164A
SANYO
SANYO -> Panasonic
componentes Descripción : 16-Bit SINGLE-Chip Microcontroller WITH On-Chip 64K-Word FLASH EEPROM and 1K-Word RAM

Overview
The LC62F0164A SINGLE chip microcontroller integrates 64K words (128K bytes) of FLASH EEPROM for progRAM and data storage, 1K words (2K bytes) of internal RAM, 2 sets of timers (CAN be used as four timers), 2 channels of serial interfaces. The SANYO original high speed 16 bit CPU core (SNAIL) is used in the chip.

The LC62F0164A operates on 100 nS cycle time and most of instructions are one-word/one -cycle. The special architecture of the SNAIL core realizes both high speed operation and efficient code side. The instruction set of the SNAIL is simplified by disposing the instructions that are not frequently used. Simplified instruction set realized small core size like 8 bit microcontrollers and high speed operation like high performance 16 bit or 32 bit RISC chip. The SNAIL CPU core comprises high speed multiplier. The multiplier executes 16×16->32 bits multiplication in two cycles.

The LC62F0164A has 1M bit FLASH EEPROM for progRAM and data storage. The contents of the FLASH EEPROM CAN be written by three ways : parallel progRAMming using EPROM progRAMmer, on board progRAMming using serial data input and data re-writing by progRAM control. Using the data rewrite function by progRAM control, the LC62F0164A CAN eliminate the external FLASH EEPROM which is used in variety of applications.

componentes Descripción : 8/16-BIT FLASH MCU FAMILY WITH RAM, EEPROM AND J1850 BLPD

The ST92F120 microcontroller is developed and manufactured by STMicroelectronics using a proprietary n-well HCMOS process. Its performance derives from the use of a flexible 256-register progRAMming model for ultra-fast context switching and real-time event response. The intelligent on chip peripherals offload the ST9 core from I/O and data management processing tasks allowing critical application tasks to get the maximum use of core resources. The new-generation ST9 MCU devices now also support low power consumption and low VOLTAGE operation for power-efficient and low-cost embedded systems.


Número de pieza(s) : ST7250 ST7250A6 ST7250B4
ST-Microelectronics
STMicroelectronics
componentes Descripción : 8-BIT MCU FOR CAN WITH 32K ROM, 1K RAM, EEPROM, ADC, WDG, PWM/BRM, 2 TIMERS, SPI AND SCI INTERFACES

8-BIT MCU FOR CAN WITH 32K ROM, 1K RAM, EEPROM, ADC, WDG, PWM/BRM, 2 TIMERS, SPI AND SCI INTERFACES

componentes Descripción : Enhanced A/D FLASH Type MCU 8-Bit MCU WITH EEPROM

General Description

The HT66FXX series of devices are FLASH Memory A/D type 8-bit high performance RISC architecture microcontrollers. Offering users the convenience of FLASH Memory multi-progRAMming features, these devices also include a wide range of functions and features. Other memory includes an area of RAM Data Memory as well as an area of EEPROM memory for storage of non-volatile data such as serial numbers, calibration data etc.


ST-Microelectronics
STMicroelectronics
componentes Descripción : 16-bit MCU WITH 256 Kbyte FLASH memory and 20 Kbyte RAM

Introduction

The ST10F272 device is a derivative of the STMicroelectronics ST10 FAMILY of 16-bit SINGLE chip CMOS microcontrollers.

The ST10F272 combines high CPU performance (up to 32 million instructions per second) WITH high peripheral functionality and enhanced I/O-capabilities. It also provides on-chip high-speed SINGLE VOLTAGE FLASH memory, on-chip high-speed RAM, and clock generation via PLL.

ST10F272 is processed in 0.18µm CMOS technology. The MCU core and the logic is supplied WITH a 5V to 1.8V on-chip VOLTAGE regulator. The part is supplied WITH a SINGLE 5V ly and I/Os work at 5V.



Features

■ 16-bit CPU WITH DSP functions

   – 31.25ns instruction cycle time at 64MHz max CPU clock

   – Multiply/accumulate unit (MAC) 16 x 16-bit multiplication, 40-bit accumulator

   – Enhanced boolean bit manipulations

   – SINGLE-cycle context switching support

■ On-chip memories

   – 256 Kbyte FLASH memory (32-bit fetch)

   – SINGLE VOLTAGE FLASH memories WITH erase/progRAM controller and 100K erasing/progRAMming cycles.

   – Up to 16 Mbyte linear address space for code and data (5 Mbytes WITH CAN or I2C)

   – 2 Kbyte internal RAM (IRAM)

   – 18 Kbyte extension RAM (XRAM)

   – ProgRAMmable external bus configuration & characteristics for different address ranges

   – Five progRAMmable chip-select signals

   – Hold-acknowledge bus arbitration support

■ Interrupt

   – 8-channel peripheral event controller for SINGLE cycle interrupt driven data transfer

   – 16-priority-level interrupt system WITH 56 sources, sampling rate down to 15.6ns

■ Timers

   – Two multi-functional general purpose timer units WITH 5 timers

■ Two 16-channel capture / compare units

■ 4-channel PWM unit + 4-channel XPWM

■ A/D converter

   – 24-channel 10-bit

   – 3 µs minimum conversion time

■ Serial channels

   – Two synch. / asynch. serial channels

   – Two high-speed synchronous channels

   – One I2C standard interface

■ 2 CAN 2.0B interfaces operating on 1 or 2 CAN busses (64 or 2x32 message, C-CAN version)

■ Fail-safe protection

   – ProgRAMmable watchdog timer

   – Oscillator watchdog

■ On-chip bootstrap loader

■ Clock generation

   – On-chip PLL WITH 4 to 8 MHz oscillator

   – Direct or prescaled clock input

■ Real time clock and 32 kHz on-chip oscillator

■ Up to 111 general purpose I/O lines

   – Individually progRAMmable as input, output or special function

   – ProgRAMmable threshold (hysteresis)

■ Idle, power down and stand-by modes

SINGLE VOLTAGE supply: 5V ±10%



 


ST-Microelectronics
STMicroelectronics
componentes Descripción : 16-bit MCU WITH 512 Kbyte FLASH memory and 36 Kbyte RAM

Introduction

The ST10F273 device is a derivative of the STMicroelectronics ST10 FAMILY of 16-bit SINGLE chip CMOS microcontrollers.

The ST10F273 combines high CPU performance (up to 32 million instructions per second) WITH high peripheral functionality and enhanced I/O-capabilities. It also provides on-chip high-speed SINGLE VOLTAGE FLASH memory, on-chip high-speed RAM, and clock generation via PLL.

ST10F273 is processed in 0.18mm CMOS technology. The MCU core and the logic is supplied WITH a 5 V to 1.8 V on-chip VOLTAGE regulator. The part is supplied WITH a SINGLE 5 V supply and I/Os work at 5 V.



Features

■ High performance 16-bit CPU WITH DSP functions

– 31.25ns instruction cycle time at 64 MHz max CPU clock

– Multiply/accumulate unit (MAC) 16 x 16-bit multiplication, 40-bit accumulator

– Enhanced boolean bit manipulations

SINGLE-cycle context switching support

■ Memory organization

– 512 Kbyte on-chip FLASH memory SINGLE VOLTAGE WITH erase/progRAM controller (full performance, 32-bit fetch)

– 100K erasing/progRAMming cycles.

– Up to 16 Mbyte linear address space for code and data (5 Mbytes WITH CAN or I2C)

– 2 Kbyte on-chip internal RAM (IRAM)

– 34 Kbyte on-chip extension RAM (XRAM)

– ProgRAMmable external bus configuration & characteristics for different address ranges

– 5 progRAMmable chip-select signals

– Hold-acknowledge bus arbitration support

■ Interrupt

– 8-channel peripheral event controller for SINGLE cycle interrupt driven data transfer

– 16-priority-level interrupt system WITH 56 sources, sampling rate down to 15.6ns

■ Timers

– 2 multifunctional general purpose timer units WITH 5 timers

■ Two 16-channel capture / compare units

■ 4-channel PWM unit + 4-channel XPWM

■ A/D Converter

– 24-channel 10-bit

– 3µs Minimum conversion time

■ Serial channels

– 2 synch. / asynch. serial channels

– 2 high-speed synchronous channels

– I2C standard interface

■ 2 CAN 2.0B interfaces operating on 1 or 2 CAN busses (64 or 2x32 messages, C-CAN version)

■ Fail-safe protection

– ProgRAMmable watchdog timer

– Oscillator watchdog

■ On-chip bootstrap loader

■ Clock generation

– On-chip PLL and 4 to 12 MHz oscillator

– Direct or prescaled clock input

■ Real time clock and 32kHz on-chip oscillator

■ Up to 111 general purpose I/O lines

– Individually progRAMmable as input, output or special function

– ProgRAMmable threshold (hysteresis)

■ Idle, power down and stand-by modes

SINGLE VOLTAGE supply: 5 V ±10%.


Número de pieza(s) : XA-G39 PXAG39KBA
Philips
Philips Electronics
componentes Descripción : XA 16-bit microcontroller FAMILY 32K FLASH/1K RAM, watchdog, 2 UARTs

GENERAL DESCRIPTION
The XA-G39 is a member of Philips’ 80C51 XA (eXtended Architecture) FAMILY of high performance 16-bit SINGLE-chip microcontrollers.

FEATURES
• 32 kbytes of on-chip FLASH progRAM memory WITH In-System ProgRAMming capability
• Three FLASH blocks = two 8 kbyte blocks and one 16 kbyte block
• Provides FLASH solution for XA-G37 (OTP) designs
SINGLE supply VOLTAGE In-System ProgRAMming (ISP) of the FLASH memory (VPP = VDD, or VPP = 12 V if desired)
• Boot ROM contains low level FLASH progRAMming routines for In-Application ProgRAMming and a default serial loader using the UART
• 1024 bytes of on-chip data RAM
• Supports off-chip progRAM and data addressing up to 1 megabyte (20 address lines)
• Three standard counter/timers WITH enhanced features (same as XA-G3 T0, T1, and T2). All timers have a toggle output capability
• Watchdog timer
• Two enhanced UARTs WITH independent baud rates
• Seven software interrupts
• Four 8-bit I/O ports, WITH 4 progRAMmable output configurations for each pin
• 30 MHz operating frequency at 5 V
• Power saving operating modes: Idle and Power-Down. Wake-Up from power-down via an external interrupt is supported.
• 44-pin PLCC package

Número de pieza(s) : 8S003F3
ST-Microelectronics
STMicroelectronics
componentes Descripción : V alue line, 16 MHz STM8S 8-bit MCU, 8 Kbytes FLASH, 128 bytes data EEPROM, 10-bit ADC, 3 timers, UART , SPI, I2C

8S003F3 Search -----> STM8S003F3

The STM8S003x value line 8-bit microcontrollers feature 8 Kbytes FLASH progRAM memory, plus integrated true data EEPROM. The STM8S microcontroller FAMILY reference manual (RM0016) refers to devices in this FAMILY as low-density . They provide the following benefits: performance, robustness, and reduced system cost.

Device performance and robustness are ensured by integrated true data EEPROM supporting up to 100000 write/erase cycles, advanced core and peripherals made in a state-of-the art technology , a 16 MHz clock frequency , robust I/Os, independent watchdogs WITH separate clock source, and a clock security system.

The system cost is reduced thanks to high system integration level WITH internal clock oscillators, watchdog and brown-out reset.

Número de pieza(s) : EN71PL032A0A EN71PL032A0A-70CWP
Eon
Eon Silicon Solution Inc.
componentes Descripción : Base MCP Stacked Multi-Chip Product (MCP) FLASH Memory and RAM 32 Megabit (2M x 16-bit) CMOS 3.0 Volt-only Simultaneous Operation Page Mode FLASH Memory and 16 Megabit (1M x 16-bit) Pseudo Static RAM

EN71PL032A Base MCP    

Stacked Multi-Chip Product (MCP) FLASH Memory and RAM

32 Megabit (2M x 16-bit) CMOS 3.0 Volt-only Simultaneous

Operation Page Mode FLASH Memory and 16 Megabit (1M x 16-bit) Pseudo Static RAM



General Description

The EN71PL series is a product line of stacked Multi-Chip Product (MCP) packages and consists of:

■EN29PL032A (Simultaneous Read/Write) FLASH memory die.

■ Pseudo SRAM.



Distinctive Characteristics

MCP Features

■ Power supply VOLTAGE of 2.7 V to 3.3V

■ High performance

    - 70 ns

■ Package

    - 7 x 9 x 1.2mm 56 ball FBGA

■ Operating Temperature

    - 25°C to +85°C


12345678910 Next



All Rights Reserved© datasheetq.com  [Privacy Policy ] [ Request Datasheet] [Contact Us]